- 您現在的位置：買賣IC網 > PDF目錄361239 > Q67126-C2088 RF inductor, ceramic core, 2% tol, SMT, RoHS PDF資料下載
參數資料
| 型號： | Q67126-C2088 |
| 英文描述： | RF inductor, ceramic core, 2% tol, SMT, RoHS |
| 中文描述： | 集成電路釤CAN控制器 |
| 文件頁數： | 33/121頁 |
| 文件大小： | 1000K |
| 代理商： | Q67126-C2088 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁
System Reset
C501
Semiconductor Group
5-1
5
System Reset
5.1
Hardware Reset
The hardware reset function incorporated in the C501 allows for an easy automatic start-up at a
minimum of additional hardware and forces the controller to a predefined default state. The
hardware reset function can also be used during normal operation in order to restart the device. This
is particularly done when the power-down mode is to be terminated.
The RESET input is an active high input. An internal Schmitt trigger is used at the input for noise
rejection. Since the reset is synchronized internally, the RESET pin must be held high for at least
two machine cycles (24 oscillator periods) while the oscillator is running. With the oscillator running
the internal reset is executed during the second machine cycle and is repeated every cycle until
RESET goes low again.
During reset, pins ALE and PSEN are configured as inputs and should not be stimulated externally.
An external stimulation at these lines during reset activates several test modes which are reserved
for test purposes. This in turn may cause unpredictable output operations at several port pins.
A pullup resistor is internally connected to
V
CC
to allow a power-up reset with an external capacitor
only. An automatic reset can be obtained when
V
CC
is applied by connecting the RESET pin to
V
SS
via a capacitor. After
V
CC
has been turned on, the capacitor must hold the voltage level at the
RESET pin for a specific time to effect a complete reset.
A correct reset leaves the processor in a defined state. The program execution starts at location
0000H. After reset is internally accomplished the port latches of ports 0, 1, 2 and 3 default in FFH.
This leaves port 0 floating, since it is an open drain port when not used as data/address bus. All
other I/O port lines (ports 1, 2 and 3) output at one (1).
The content of the internal RAM of the C501 is not affected by a reset. After power-up the content
is undefined, while it remains unchanged during a reset if the power supply is not turned off.
相關PDF資料 |
PDF描述 |
|---|---|
| Q67127-C2036SAB-C161R1-L16M | IC-SM-16 BIT CPU |
| Q67120-C2200 | 16-Bit Single-Chip Microcontroller Bare Die Delivery |
| Q67120-C1054 | High Speed CMOS Logic Triple 3-Input NOR Gates 14-SOIC -55 to 125 |
| Q67120-C1056 | High Speed CMOS Logic Triple 3-Input NOR Gates 14-SOIC -55 to 125 |
| Q67120-C2002 | High Speed CMOS Logic Octal D-Type Flip-Flops with Reset 20-SOIC -55 to 125 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| Q67127-C1009 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Microcontroller |
| Q67127-C1014 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Microcontroller |
| Q67127-C1030 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Microcontroller |
| Q67127-C1031 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Microcontroller |
| Q67127-C1032 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Microcontroller |
發(fā)布緊急采購，3分鐘左右您將得到回復。