參數資料
型號: QW075F1
英文描述: Analog IC
中文描述: 模擬IC
文件頁數: 8/20頁
文件大?。?/td> 1008K
代理商: QW075F1
8
Lucent Technologies Inc.
Data Sheet
May 2000
dc-dc Converters; 36 to 75 Vdc Input, 3.3 Vdc Output; 33 W to 50 W
QW050F1 and QW075F1 Power Modules:
Test Configurations
8-203 (C).l
Note: Measure input reflected-ripple current with a simulated source
inductance (L
TEST
) of 12 μH. Capacitor C
S
offsets possible bat-
tery impedance. Measure current as shown above.
Figure 13. Input Reflected-Ripple Test Setup
8-513 (C).d
Note: Use a 1.0 μF ceramic capacitor and a 10 μF aluminum or tan-
talum capacitor. Scope measurement should be made using a
BNC socket. Position the load between 51 mm and 76 mm
(2 in. and 3 in.) from the module.
Figure 14. Peak-to-Peak Output Noise
Measurement Test Setup
8-749 (C)
Note: All measurements are taken at the module terminals. When
socketing, place Kelvin connections at module terminals to
avoid measurement errors due to socket contact resistance.
Figure 15. Output Voltage and Efficiency
Measurement Test Setup
Design Considerations
Input Source Impedance
The power module should be connected to a low
ac-impedance input source. Highly inductive source
impedances can affect the stability of the power mod-
ule. For the test configuration in Figure 13, a 33 μF
electrolytic capacitor (ESR < 0.7
at 100 kHz)
mounted close to the power module helps ensure sta-
bility of the unit. For other highly inductive source
impedances, consult the factory for further application
guidelines.
Safety Considerations
For safety-agency approval of the system in which the
power module is used, the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standard,
i.e., UL1950, CSAC22.2 No. 950-95, and VDE0805
(EN60950, IEC950).
If the input source is non-SELV (ELV or a hazardous
voltage greater than 60 Vdc and less than or equal to
75 Vdc), for the module’s output to be considered meet-
ing the requirements of safety extra-low voltage
(SELV), all of the following must be true:
I
The input source is to be provided with reinforced
insulation from any hazardous voltages, including the
ac mains.
I
One V
I
pin and one V
O
pin are to be grounded, or
both the input and output pins are to be kept floating.
I
The input pins of the module are not operator acces-
sible.
I
Another SELV reliability test is conducted on the
whole system, as required by the safety agencies, on
the combination of supply source and the subject
module to verify that under a single fault, hazardous
voltages do not appear at the module’s output.
Note:
Do not ground either of the input pins of the
module without grounding one of the output pins.
This may allow a non-SELV voltage to appear
between the output pin and ground.
The power module has extra-low voltage (ELV) outputs
when all inputs are ELV.
The input to these units is to be provided with a maxi-
mum 3 A normal-blow fuse in the ungrounded lead.
TO OSCILLOSCOPE
12 μH
V
I
(+)
V
I
(–)
CURRENT
PROBE
L
TEST
BATTERY
C
S
220 μF
ESR < 0.1
@ 20
°
C, 100 kHz
33 μF
ESR < 0.7
V
O
(+)
V
O
(–)
1.0 μF
RESISTIVE
LOAD
SCOPE
COPPER STRIP
10 μF
V
I
(+)
I
I
I
O
SUPPLY
CONTACT
RESISTANCE
CONTACT AND
DISTRIBUTION LOSSES
LOAD
SENSE(+)
V
I
(–)
V
O
(+)
V
O
(–)
SENSE(–)
η
O
(+) – V
O
(–)
V
I
(+) – V
I
(–)
[
-V
]
I
O
]
I
I
x 100
=
%
相關PDF資料
PDF描述
QW0905-LUR3333H SUPER BRIGHT ROUND TYPE LED LAMPS
QWD1205 Analog IC
QWD1212 Analog IC
QWD1215 Analog IC
QWD2405 Analog IC
相關代理商/技術參數
參數描述
QW0806BR 制造商:NTE Electronics 功能描述:1/4 Watt, Rn 55D, 806 Ohm 1% Metal Film Resistor- 25/Pkg
QW080D6BR 制造商:NTE Electronics 功能描述:1/4 Watt, Rn 55D, 80.6 Ohm 1% Metal Film Resistor- 25/Pkg
QW082 制造商:NTE Electronics 功能描述:Res Metal Film 82 Ohm 2% 1/4W ±200ppm/°C Conformal AXL Thru-Hole
QW0825BR 制造商:NTE Electronics 功能描述:1/4 Watt, Rn 55D, 825 Ohm 1% Metal Film Resistor- 25/Pkg
QW0905-LPD3330 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PHOTO DIODE SILICON PIN LED LAMPS