- 您現在的位置：買賣IC網 > PDF目錄376305 > RC86L50-1 (Electronic Theatre Controls, Inc.) VOICE SYNTHESIZER PDF資料下載
參數資料
| 型號： | RC86L50-1 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | VOICE SYNTHESIZER |
| 中文描述： | 語音合成器 |
| 文件頁數： | 26/48頁 |
| 文件大?。?/td> | 747K |
| 代理商： | RC86L50-1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
26
RC8650 VOICE SYNTHESIZER
RC SYSTEMS
Table 2.8. TS Pin Control
Table 2.9. Protocol Options Register Bit Definitions
Zap Commands (Z)
This command prevents the RC8650 from honoring subsequent com-
mands, causing it to read commands as they are encountered (useful
in debugging). Any pending commands in the input buffer will still
be honored. The only way to restore command recognition after the
Zap command has been issued is to write
CTRL+^
(ASCII 30) to the
RC8650 or perform a hardware reset.
Protocol Options Register (nG)
This command controls various internal RC8650 operating param-
eters. The command parameter
n
is calculated by ORing together the
individual control bits shown in Table 2.9. For example, 193G (193 =
128 + 64 + 1) disables V8600 emulation, enables all status messages
and specifies that parameters should saturate. 128G is the default
setting.
Bit POR.7 (VC) programs the RC8650 to emulate RC Systems’ original
V8600 voice synthesizer module. When this bit is set to 0 (which V8600
application programs do, as this bit was undefined in the V8600),
the overall voice speed range is reduced and the default speed is
changed from 1S to 5S, matching the characteristics of the V8600.
The serial port status messages (see Table 1.3) are also affected by
the setting of this bit.
Note
Relative parameters work differently than usual with this com-
mand. Instead of specifying a displacement from the register’s
current value, relative parameters allow you to set (“+”) and clear
(“–”) individual register bits. For example, +65G sets bits POR.0 and
POR.6; –65G clears POR.0 and POR.6.
Reinitialize (@)
This command reinitializes the RC8650 by clearing the input buffer and
restoring the voice parameters and control registers to their factory
default settings. The exception dictionary, prerecorded audio, greeting
message, baud rate, nor TS pin control setting are affected.
Stop (CTRL+X), Skip (CTRL+Y)
The Stop command stops the RC8650 and flushes its input buffer of all
text and commands. The Skip command skips to the next sentence in
the buffer. Neither command affects any of the RC8650’s settings.
Note
The format of these commands is unique in that the command
character (CTRL+A) is not used with them. The CTRL+X (ASCII 24)
and CTRL+Y (ASCII 25) characters are
written directly
to the RC8650,
which enables the RC8650 to react immediately, even if its input buf-
fer is full. To be most effective, the states of the RC8650 handshaking
signals should be ignored.
相關PDF資料 |
PDF描述 |
|---|---|
| RC86L50-2 | VOICE SYNTHESIZER |
| RC86L50-3 | VOICE SYNTHESIZER |
| RCM3200 | C-Programmable Module with Ethernet |
| RCV336ACFWSP | RCV336ACF/SP and RCV144ACF/SP Modem Device |
| RCV144ASP | RCV336ACF/SP and RCV144ACF/SP Modem Device |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RC86L50-2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:VOICE SYNTHESIZER |
| RC86L50-3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:VOICE SYNTHESIZER |
| RC86L60-1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CMOS, 3.3 Volt / 5 Volt Voice Synthesizer Chipset |
| RC86L60-2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CMOS, 3.3 Volt / 5 Volt Voice Synthesizer Chipset |
| RC86L60-3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CMOS, 3.3 Volt / 5 Volt Voice Synthesizer Chipset |
發布緊急采購，3分鐘左右您將得到回復。