- 您現在的位置：買賣IC網 > PDF目錄376309 > RH56D-PCI (Electronic Theatre Controls, Inc.) MODEM DEVICE FAMILY FOR DESKTOP APPLICATIONS PDF資料下載
參數資料
| 型號： | RH56D-PCI |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | MODEM DEVICE FAMILY FOR DESKTOP APPLICATIONS |
| 中文描述： | 調制解調器設備家庭桌面應用程序 |
| 文件頁數： | 37/60頁 |
| 文件大?。?/td> | 357K |
| 代理商： | RH56D-PCI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁
RH56D-PCI Modem Designer’s Guide
1213
Conexant
4-3
Conexant Proprietary Information
on one side only, then the isolation trace can be kept contiguous by briefly passing it to the other side of the PCB to jump
over the signal traces.
10. Avoid right angle (90 degree) turns on high frequency traces. Use smoothed radiuses or 45 degree corners.
11. Minimize the number of through-hole connections (feedthroughs/vias) on traces carrying high frequency signals.
12. Keep all signal traces away from crystal circuits.
13. Distribute high frequency signals continuously on a single trace rather than several traces radiating from one point.
14. Provide adequate clearance (e.g., 60 mil minimum) around feedthroughs in any internal planes in the DAA circuit.
15. Eliminate ground loops, which are unexpected current return paths to the power source.
16. Route PCICLK in accordance with Section 4.2.3.
4.1.4 Power
1. Identify digital power (VDD) and analog power (AVDD) supply connections.
2. Place a 10 μF electrolytic or tantalum capacitor in parallel with a ceramic 0.1 μF capacitor between power and ground at
one or more points in the digital section. Place one set nearest to where power enters the PCB (edge connector or power
connector) and place another set at the furthest distance from where power enters the PCB. These capacitors help to
supply current surge demands by the digital circuits and prevent those surges from generating noise on the power lines
that may affect other circuits.
3. For 2-layer boards, route a 200-mil wide power trace on two edges of the same side of the PCB around the border of the
circuits using the power. (Note that a digital ground trace should likewise be routed on the other side of the board.)
4. Generally, route all power traces before signal traces.
相關PDF資料 |
PDF描述 |
|---|---|
| RH56D-PCI | Host Controlled V.90/K56flex Modem device |
| RHF-24(2) | LOW-POWER DISSIPATION ADSL LINE DRIVER |
| RI-60 | Ultra-miniature dry-reed switch hermetically sealed in a gas-filled glass envelope |
| RI60 | Ultra-miniature dry-reed switch germetically sealed in a gas-dilled glass envelope |
| RI-ANT-S01C-00 | SERIES 2000 ANTENNAS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RH56M-4/122156 | 制造商:ebm-papst Inc 功能描述: |
| RH56M-4/210928 | 制造商:ebm-papst Inc 功能描述: |
| RH56M-6/127804 | 制造商:ebm-papst Inc 功能描述: |
| RH56M-6/204689 | 制造商:ebm-papst Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。