參數資料
型號： RTL8100
廠商： Electronic Theatre Controls, Inc.
英文描述： REALTEK SINGLE CHIP FAST ETHERNET CONTROLLER WITH POWER MANAGEMENT
中文描述： 瑞昱單芯片快速以太網控制器電源管理
文件頁數： 31/58頁
文件大?。?/td> 657K
代理商： RTL8100
RTL8100B(L)
2001-11-9
Rev.1.41
31
5.28 Config5: Configuration Register 5
(Offset 00D8h, R/W)
This register, unlike other Config registers, is not protected by 93C46 Command register. I.e. there is no need to enable Config
register write prior to writing to Config5.
Bit
7
6
R/W
-
R/W
Symbol
-
BWF
Description
Reserved
Broadcast Wakeup Frame:
1: Enable Broadcast Wakeup Frame with mask bytes of only DID
field = FF FF FF FF FF FF.
0: Default value. Disable Broadcast Wakeup Frame with mask bytes
of only DID field = FF FF FF FF FF FF.
The power-on default value of this bit is 0.
Multicast Wakeup Frame:
1: Enable Multicast Wakeup Frame with mask bytes of only DID
field, which is a multicast address.
0: Default value. Disable Multicast Wakeup Frame with mask bytes
of only DID field, which is a multicast address.
The power-on default value of this bit is 0.
Unicast Wakeup Frame:
1: Enable Unicast Wakeup Frame with mask bytes of only DID field,
which is its own physical address.
0: Default value. Disable Unicast Wakeup Frame with mask bytes of
only DID field, which is its own physical address.
The power-on default value of this bit is 0.
FIFO Address Pointer:
(Realtek internal use only to test FIFO SRAM)
1: Both Rx and Tx FIFO address pointers are updated in descending
way from 1FFh and downwards. The initial FIFO address pointer is
1FFh.
0: (Power-on) default value. Both Rx and Tx FIFO address pointers
are updated in ascending way from 0 and upwards. The initial FIFO
address pointer is 0.
Note: This bit does not participate in EEPROM auto-load. The FIFO
address pointers can not be reset, except initial power-on.
The power-on default value of this bit is 0.
Link Down Power Saving mode:
1: Disable.
0: Enable. When cable is disconnected(Link Down), the analog part
will power down itself (PHY Tx part & part of twister) automatically
except PHY Rx part and part of twister to monitor SD signal in case
that cable is re-connected and Link should be established again.
LANWake signal enable/disable:
1: Enable LANWake signal.
0: Disable LANWake signal.
PME_Status bit:
Always sticky/can be reset by PCI RST# and software.
1: The PME_Status bit can be reset by PCI reset or by software.
0: The PME_Status bit can only be reset by software.
5
R/W
MWF
4
R/W
UWF
3
R/W
FIFOAddrPtr
2
R/W
LDPS
1
R/W
LANWake
0
R/W
PME_STS
Config5 register, offset D8h: (SYM_ERR register is changed to Config5, the function of SYM_ERR register is no longer
supported by RTL8100B(L).)
The 3 bits (bit2-0) are auto-loaded from EEPROM Config5 byte to RTL8100B(L) Config5 register.
相關PDF資料
PDF描述
RTL8100B REALTEK SINGLE CHIP FAST ETHERNET CONTROLLER WITH POWER MANAGEMENT
RTL8100BL REALTEK SINGLE CHIP FAST ETHERNET CONTROLLER WITH POWER MANAGEMENT
RTL8100BLLQTP REALTEK SINGLE CHIP FAST ETHERNET CONTROLLER WITH POWER MANAGEMENT
RTL8100BQFP REALTEK SINGLE CHIP FAST ETHERNET CONTROLLER WITH POWER MANAGEMENT
RTL8100L REALTEK SINGLE CHIP FAST ETHERNET CONTROLLER WITH POWER MANAGEMENT
相關代理商/技術參數
參數描述
RTL8100B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:REALTEK SINGLE CHIP FAST ETHERNET CONTROLLER WITH POWER MANAGEMENT
RTL8100B(L) 制造商:未知廠家 制造商全稱:未知廠家 功能描述:RTL8100B(L) Specification
RTL8100BL 制造商:未知廠家 制造商全稱:未知廠家 功能描述:REALTEK SINGLE CHIP FAST ETHERNET CONTROLLER WITH POWER MANAGEMENT
RTL8100BLLQTP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:REALTEK SINGLE CHIP FAST ETHERNET CONTROLLER WITH POWER MANAGEMENT
RTL8100BQFP 制造商:未知廠家 制造商全稱:未知廠家 功能描述:REALTEK SINGLE CHIP FAST ETHERNET CONTROLLER WITH POWER MANAGEMENT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*