參數資料
型號: S108T02
廠商: SHARP ELECTRONICS CORP
元件分類: 繼電器,輸入/輸出模塊
英文描述: TRIGGER OUTPUT SOLID STATE RELAY, 3000 V ISOLATION-MAX
封裝: PLASTIC, SIP-4
文件頁數: 12/13頁
文件大?。?/td> 240K
代理商: S108T02
8
S108T02 Series
S208T02 Series
■ Design Considerations
In order for the SSR to turn off, the triggering current (lF) must be 0.1mA or less.
When the input current (IF) is below 0.1mA, the output Triac will be in the open circuit mode. However, if the
voltage across the Triac, VD, increases faster than rated dV/dt, the Triac may turn on. To avoid this situation,
please incorporate a snubber circuit. Due to the many different types of load that can be driven, we can
merely recommend some circuit vales to start with : Cs=0.022F and Rs=47. The operation of the SSR
and snubber circuit should be tested and if unintentional switching occurs, please adjust the snubber circuit
component values accordingly.
When making the transition from On to Off state, a snubber circuit should be used ensure that sudden drops
in current are not accompanied by large instantaneous changes in voltage across the Triac.
This fast change in voltage is brought about by the phase difference between current and voltage.
Primarily, this is experienced in driving loads which are inductive such as motors and solenoids.
Following the procedure outlined above should provide sufficient results.
For over voltage protection, a Varistor may be used.
Any snubber or Varistor used for the above mentioned scenarios should be located as close to the main out-
put triac as possible.
Particular attention needs to be paid when utilizing SSRs that incorporate zero crossing circuitry.
If the phase difference between the voltage and the current at the output pins is large enough, zero crossing
type SSRs cannot be used. The result, if zero crossing SSRs are used under this condition, is that the SSR
may not turn on and off irregardless of the input current. In this case, only a non zero cross type SSR should
be used in combination with the above mentioned snubber circuit selection process.
The load current should be within the bounds of derating curve. (Refer to Fig.2)
Also, please use the optional heat sink when necessary.
In case the optional heat sink is used and the isolation voltage between the device and the optional heat sink
is needed, please locate the insulation sheet between the device and the heat sink.
When the optional heat sink is equipped, please set up the M3 screw-fastening torque at 0.3 to 0.5Nm.
In order to dissipate the heat generated from the inside of device effectively, please follow the below sugges-
tions.
● Design guide
Sheet No.: D4-A01801EN
Recommended Operating Conditions
Parameter
S108T02
S208T02
Symbol
Unit
Input
Output
Input signal current at ON state
Input signal current at OFF state
Load supply voltage
Load supply current
Frequency
Operating temperature
IF(ON)
IF(OFF)
VOUT(rms)
IOUT(rms)
f
Topr
mA
V
mA
Hz
C
Locate snubber circuit between output terminals
(Cs
=0.022F, Rs=47)
Conditions
() See Fig.2 about derating curve (IT(rms) vs. ambient temperature).
16
0
80
0.1
47
20
24
0.1
120
240
IT(rms)
×80%()
63
80
MIN.
MAX.
相關PDF資料
PDF描述
S112S01 TRIGGER OUTPUT SOLID STATE RELAY, 4000 V ISOLATION-MAX
S112S02 TRIGGER OUTPUT SOLID STATE RELAY, 4000 V ISOLATION-MAX
S212S02 TRIGGER OUTPUT SOLID STATE RELAY, 4000 V ISOLATION-MAX
S11MD5TS 1 CHANNEL TRIAC OUTPUT OPTOCOUPLER
S11MD5VP 1 CHANNEL TRIAC OUTPUT OPTOCOUPLER
相關代理商/技術參數
參數描述
S108T02F 功能描述:固態繼電器-PCB安裝 4-SIP ZERO-C 8mA RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT
S109 功能描述:TOOL LONG NOSE MICRO SERRATED 4" RoHS:是 類別:工具 >> 鉗子、扳手 系列:Super Tools™ 標準包裝:1 系列:- 尖端 - 類型:針頭,直形 工具類型:鉗子 特點:人機工程型手柄,ESD 安全,鋸齒狀 長度:5.75"(146.05mm) 重量:0.23 磅(104.33g)
S-109 制造商:Leach International Corporation 功能描述:LRE - Bulk
S-1091-A 制造商:Molex 功能描述:
S-1091-A-SP 制造商:Molex 功能描述: