- 您現在的位置：買賣IC網 > PDF目錄385812 > SA56600-42 (NXP Semiconductors N.V.) System reset for lithium battery backup PDF資料下載
參數資料
| 型號： | SA56600-42 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | System reset for lithium battery backup |
| 中文描述： | 系統復位備用鋰電池 |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 141K |
| 代理商： | SA56600-42 |
Philips Semiconductors
Product data
SA56600-42
System reset for lithium battery back-up
2001 Jun 19
7
TECHNICAL DESCRIPTION
The SA56600-42 provides battery back-up functions to protect
SRAM data in computer memory systems. In addition, it provides
RESET, Chip Select HIGH (CS), and Chip Select LOW (CS)
outputs. The device incorporates a 3.3 V detection circuit,
4.2 V detection circuit, PNP switching transistor, and Schottky diode
for low drop lithium battery connection to the output.
During power-up, RESET is actively asserted (LOW logic state) at
V
CC
voltages as low as 0.8 V and does not output a release (HIGH
logic state) until V
CC
attains 4.2 V plus hysteresis. CS, in a similar
manner, only transitions to a HIGH logic state when V
CC
attains
4.2 V plus hysteresis. This ensures adequate voltage being present
at the output of the SA56600 for proper operation of the associated
computer system.
If the V
CC
voltage falls below 4.2 V, CS and RESET both go to a
LOW logic state. During this time, with CS in a LOW logic state, no
data ca be read from, or written to, the SRAM device. If the primary
voltage (V
CC
) continues to fall to 3.3 V and below, the PNP
switching transistor disconnects the primary input source power
(V
CC
) from the output and the Schottky diode automatically couples
the lithium battery power to the output of the SA56600 to supply
sustaining power to the SRAM memory.
The SA56600 provides complementary CS and CS outputs. The
outputs differ in ways other than being simple complements of each
other. The logic state of CS is strictly a function of V
CC
voltage.
When V
CC
is above 4.2 V plus hysteresis, CS is in a HIGH logic
state. When V
CC
is below 4.2 V, CS is in a LOW logic state.
CS goes to a LOW logic state only when V
CC
is above 4.2 V plus
hysteresis, and Y is simultaneously at a LOW logic state. If Y is not
a LOW logic state (is open or at a HIGH logic state) CS will be at a
HIGH logic state. Essentially, Y functions as a control switch for CS
and is normally used as an input gating signal from the computer’s
microprocessor.
Caution should be exercised in the application to keep the voltage
on Y to less than 5.0 V when the V
CC
voltage is less than 4.2 V to
avoid breaking down the Emitter-Base junction of the internal NPN
transistor associated with Y. Breakdown of the junction may produce
excessive current flow causing damage to the device. When the
V
CC
voltage is less than 4.2 V, the base of the NPN transistor
associated with the Y is at a LOW logic state and most susceptible
to an overvoltage on Y.
Recovering primary V
CC
power is sensed by the 3.3 V detection
circuit. The PNP switching transistor is activated when the applied
V
CC
voltage reaches 3.3 V plus hysteresis. When this event occurs,
the Schottky diode becomes back-biased, automatically
disconnecting the lithium battery from the output and the SRAM is
once again supported by the primary V
CC
power source. Full
operation is restored when the applied primary V
CC
voltage reaches
the required 4.2 V plus hysteresis value. This level is sensed by the
4.2 V detection circuit. RESET and CS are then caused to go to a
HIGH logic state, and the computer memory is back in full operation
without any loss of SRAM data.
SL01342
1
1
4
8
7
Y
5
3
2
V
CC
GND
CS
CS
RESET
V
OUT
C1
C2
R1
V
BATT
GND
6
LITHIUM
BATTERY
VOLTAGE
TO SRAM
PNP
SWITCHING
TRANSISTOR
R
R
R
R
R
R
R
R
R1 = OVERVOLTAGE CURRENT LIMITING RESISTOR
C1, C2 = POWER SUPPLY BYPASS CAPACITOR
R
R
R
47 k
R
R
47 k
R
R
R
R
R
R
SA56600–42
Figure 14. Functional diagram.
相關PDF資料 |
PDF描述 |
|---|---|
| SA56614-42 | CMOS system reset |
| SA568A | Ceramic Multilayer Capacitor; Capacitor Type:General Purpose; Capacitance:2200pF; Capacitance Tolerance: 10%; Voltage Rating:100VDC; Capacitor Dielectric Material:Multilayer Ceramic; Package/Case:0603; Termination:SMD RoHS Compliant: Yes |
| SA568AD | 150MHz phase-locked loop |
| SA568AN | 150MHz phase-locked loop |
| SA577N | Unity gain level programmable low power compandor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SA56606-20 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:CMOS system reset |
| SA56606-20GW | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:CMOS system reset |
| SA56606-27 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:CMOS system reset |
| SA56606-27GW | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:CMOS system reset |
| SA56606-28 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:CMOS system reset |
發布緊急采購，3分鐘左右您將得到回復。