參數資料
型號： SAA2023GP
廠商： NXP SEMICONDUCTORS
元件分類： 消費家電
英文描述： Drive processor for DCC systems
中文描述： SPECIALTY CONSUMER CIRCUIT, PQFP80
封裝： 14 X 20 MM, 2.70 MM HEIGHT, PLASTIC, SOT-318-2, QFP-80
文件頁數： 12/56頁
文件大?。?/td> 274K
代理商： SAA2023GP
May 1994
12
Philips Semiconductors
Preliminary specification
Drive processor for DCC systems
SAA2023
Table 11
SH1 and SH2 (FIR output scaling).
Transfer of FIR coefficients
For the main data channels (tracks 0 to 7) there are
10 coefficients (taps) each of 8 bits, where all of the data
channels make use of the same coefficients. The
addresses for the main data coefficients 0 to 9 are
0 to 9
dec
respectively.
There are ten coefficients (taps) each of 8 bits for the aux
channel (CHAUX). The addresses for the auxiliary
coefficients 0 to 9 are 16 to 25
dec
respectively.
SH
EFFECT ON FIR OUTPUT
1
0
0
0
0
1
FIR mod 256
mod 256
1
0
mod 256
1
1
mod 256
2
FIR
F4
8
FIR
There are 2 banks of coefficients for both the aux and the
main data channels, namely the ‘buffer’, and the ‘a(chǎn)ctive’
banks. The microcontroller writes only to the ‘buffer’
banks, and reads only from the ‘a(chǎn)ctive’ banks.
The microcontroller can poll the digital equalizer status bit
BKSW to see when the switch occurs. BKSW starts life
LOW, goes HIGH as a result of the bank switching and
goes LOW as result of the complete value of a main data
coefficient being received by the digital equalizer.
The microcontroller sets
μ
CS HIGH before sending the
new set of aux or main data coefficients, the digital
equalizer resets it once the bank switch occurs.
The actual FIR coefficients that are used are a function of
the tape head, read amplifier and type of tape (i.e.
pre-recorded or own recorded) used, such information is
outside of the scope of this data sheet.
Coefficient address counter (COEFCNT)
This 5 bit counter is used to point to the FIR coefficient to
be transferred to or from the digital equalizer.
Table 12
Coefficient address counter.
BIT
7
0
6
0
5
0
4
3
2
1
0
Meaning
Default
CC4
0
CC3
0
CC2
0
CC1
0
CC0
0
Pin explanations and interfacing to other hardware
RESET
This is an active HIGH input which resets the SAA2023
and brings it into its default mode, DPAP. This reset does
not affect the contents of the FIR filter coefficients in the
digital equalizer. This should be connected to the system
reset, which can be driven by the microcontroller. The
duration of the reset pulse should be at least 15
μ
s.
SLEEP
This pin is an active HIGH input which puts the SAA2023
in a low power consumption SLEEP mode. This pin should
be connected to the DCC SLEEP signal, which can be
driven by the microcontroller. The CLK24 clock may be
stopped and the VREFP and VREFN inputs brought to
ground while the SAA2023 is in ‘sleep’ mode to further
reduce power consumption. When recovering from sleep
mode, the SLEEP pin should be taken LOW and the
SAA2023 reset.
CLK24
This is the 24.576 MHz clock input and should be
connected directly to the SAA2003 (pin CLK24).
Sub-band serial PASC interface connections
The timing for the sub-band serial PASC interface is given
in Figs 5 to 7.
相關PDF資料
PDF描述
SAA2023 Drive processor for DCC systems
SAA2023H RES 4.53K OHM 1/16W 0.5% 0402SMD
SAA2500 MPEG Audio Source Decoder
SAA2500H MPEG Audio Source Decoder
SAA2501 Digital Audio Broadcast DAB decoder
相關代理商/技術參數
參數描述
SAA2023H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Drive processor for DCC systems
SAA2032 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital equalization for the tape drive processing of the DCC system
SAA2032GP 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital equalization for the tape drive processing of the DCC system
SAA-21 制造商:GENERAL DEVICES 功能描述:CHASSIS SUPPORT ANGLES, Sold in a Set of 2
SAA2140 制造商:Molex 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*