- 您現在的位置：買賣IC網 > PDF目錄372112 > SAA567X (NXP Semiconductors N.V.) Enhanced TV microcontrollers with On-Screen Display (OSD) PDF資料下載
參數資料
| 型號： | SAA567X |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Enhanced TV microcontrollers with On-Screen Display (OSD) |
| 中文描述： | 與微控制器在強化電視屏幕顯示（OSD） |
| 文件頁數： | 44/116頁 |
| 文件大?。?/td> | 532K |
| 代理商： | SAA567X |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁當前第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁
2002 May 06
44
Philips Semiconductors
Objective specification
Enhanced TV microcontrollers with
On-Screen Display (OSD)
SAA567x; SAA569x
13.2.2
A
UTO
-
RELOAD MODE
In the Auto-reload mode, Timer 2 can be programmed to
count up/down by clearing/setting bit DCEN in T2MOD.
13.2.3
C
OUNTING UP
(DCEN = 0)
In the Auto-reload mode and when counting up, registers
RCAP2L/RCAP2H are used to hold a reload value for
TL2/TH2 when Timer 2 rolls over. By setting/clearing
bit EXEN2 in T2CON, external trigger T2EX on Port 3.4
can be enabled/disabled. If EXEN2 = 0, Timer 2 is a 16-bit
timer/counter which, upon overflow, sets TF2 and reloads
TL2/TH2 with the reload value in RCAP2L/RCAP2H.
If EXEN2 = 1, Timer 2 does the above, but with the added
feature that a HIGH-to-LOW transition at the external
trigger T2EX on Port 3.4 causes the current
RCAP2L/RCAP2H value to be loaded into TL2/TH2
respectively, and bit EXF2 in T2CON to be set.
Timer 2 interrupt is set if EXF2 or TF2 is set.
13.2.4
C
OUNTING UP
(DCEN = 1
AND
T2EX = 1)
In this mode Timer 2 counts up. When Timer 2 overflows
(FFFFH state), bit TF2 is set. This reloads TL2 and TH2
with the contents of RCAP2L and RCAP2H, respectively.
On overflow, bit EXF2 is inverted and hence toggles
during operation, so that bit EXF2 can be used as 17
th
bit,
if desired.
Timer 2 interrupt will be set only if TF2 is set.
13.2.5
C
OUNTING DOWN
(DCEN = 1
AND
T2EX = 0)
In this mode Timer 2 counts down. Underflow will occur
when the contents of TL2/TH2 match the contents of
RCAP2L/RCAP2H. A Timer 2 roll-over from 0000H to
FFFFH is not considered as an underflow. Upon
underflow,bit TF2willbesetandregisters TL2/TH2willbe
loaded with FFFFH. In addition, an underflow will cause
bit EXF2 to be inverted, such that it can be used as the
17
th
bit, if desired.
Timer 2 interrupt is set only if TF2 is set.
13.2.6
B
AUD RATE GENERATION MODE
In this mode, timer overflow will load TL2 and TH2 with the
contents of T2CAPL and T2CAPH respectively and it will
not set TF2. Bit EXF2 will be set if EXEN2 is set and a
HIGH-to-LOW transition is detected on pin T2EX
(Port 3.4).
When Timer 2 is configured for timer operation, the timer
increments every state. Normally, as a timer, it would
increment every machine cycle.
Timer 2 interrupt is set only if EXF2 is set.
13.2.7
C
LOCK OUTPUT MODE
Intheclockoutputmode,externalpin T2isusedasaclock
output. A timer overflow causes TL2 and TH2 to be loaded
with T2CAPL and T2CAPH, respectively. An overflow
toggles bit EXF2, which is connected to pin T2. The
frequency of T2 will be half the overflow frequency. Timer
overflow will not set TF2. A HIGH-to-LOW transition on the
external trigger T2EX on Port 3.4 sets EXF2. It is possible
toconfigureTimer 2inclock-outmodeandbaudgenerator
mode simultaneously.
Timer 2 interrupt is set only if EXF2 is set.
14 WATCHDOG TIMER
The Watchdog Timer is a counter that, once in an overflow
state, forces the microcontroller into a reset condition. The
purpose of the Watchdog Timer is to reset the
microcontroller if it enters an erroneous processor state
(possibly caused by electrical noise or RFI) within a
reasonable period of time. When enabled, the Watchdog
circuit generates a system reset if the user program fails to
reload the Watchdog Timer within a specified length of
time, known as the Watchdog interval.
The Watchdog Timer consists of an 8-bit counter with a
16-bit prescaler. The prescaler is fed with a signal whose
frequency is
1
6
f
clk
(2 MHz for 12 MHz 80C51 core). The
8-bit counter is incremented every ‘t’ seconds where:
t
6
clk
f
×
2
16
×
6
65536
12 MHz
×
32.768 ms
=
=
=
相關PDF資料 |
PDF描述 |
|---|---|
| SAA5695HL | Enhanced TV microcontrollers with On-Screen Display (OSD) |
| SAA569x | Enhanced TV microcontrollers with On-Screen Display (OSD) |
| SAA5677HL | Enhanced TV microcontrollers with On-Screen Display (OSD) |
| SAA5700GP | Chinese Character System Teletext CCST decoder |
| SAA5700 | Chinese Character System Teletext CCST decoder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAA5695HL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Enhanced TV microcontrollers with On-Screen Display (OSD) |
| SAA5697HL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Enhanced TV microcontrollers with On-Screen Display (OSD) |
| SAA569X | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Enhanced TV microcontrollers with On-Screen Display (OSD) |
| SAA5700 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Chinese Character System Teletext CCST decoder |
| SAA5700GP | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Chinese Character System Teletext CCST decoder |
發布緊急采購，3分鐘左右您將得到回復。