參數資料
型號： SAK-C164CI-8EMCB
廠商： INFINEON TECHNOLOGIES AG
元件分類： 微控制器/微處理器
英文描述： 16-BIT, OTPROM, 20 MHz, MICROCONTROLLER, PQFP80
封裝： 0.65 MM PITCH, METRIC, PLASTIC, QFP-80
文件頁數： 20/80頁
文件大小： 1337K
代理商： SAK-C164CI-8EMCB
C164CI/SI
C164CL/SL
Data Sheet
22
V2.0, 2001-05
General Purpose Timer (GPT) Unit
The GPT unit represents a very flexible multifunctional timer/counter structure which
may be used for many different time related tasks such as event timing and counting,
pulse width and duty cycle measurements, pulse generation, or pulse multiplication.
The GPT unit incorporates three 16-bit timers. Each timer may operate independently in
a number of different modes, or may be concatenated with another timer.
Each of the three timers T2, T3, T4 of module GPT1 can be configured individually for
one of four basic modes of operation, which are Timer, Gated Timer, Counter, and
Incremental Interface Mode. In Timer Mode, the input clock for a timer is derived from
the CPU clock, divided by a programmable prescaler, while Counter Mode allows a timer
to be clocked in reference to external events.
Pulse width or duty cycle measurement is supported in Gated Timer Mode, where the
operation of a timer is controlled by the ‘gate’ level on an external input pin. For these
purposes, each timer has one associated port pin (TxIN) which serves as gate or clock
input. The maximum resolution of the timers in module GPT1 is 16 TCL.
The count direction (up/down) for each timer is programmable by software or may
additionally be altered dynamically by an external signal on a port pin (TxEUD) to
facilitate e.g. position tracking.
In Incremental Interface Mode the GPT1 timers (T2, T3, T4) can be directly connected
to the incremental position sensor signals A and B via their respective inputs TxIN and
TxEUD. Direction and count signals are internally derived from these two input signals,
so the contents of the respective timer Tx corresponds to the sensor position. The third
position sensor signal TOP0 can be connected to an interrupt input.
Timer T3 has an output toggle latch (T3OTL) which changes its state on each timer over-
flow/underflow. The state of this latch may be used internally to clock timers T2 and T4
for measuring long time periods with high resolution.
In addition to their basic operating modes, timers T2 and T4 may be configured as reload
or capture registers for timer T3. When used as capture or reload registers, timers T2
and T4 are stopped. The contents of timer T3 is captured into T2 or T4 in response to a
signal at their associated input pins (TxIN). Timer T3 is reloaded with the contents of T2
or T4 triggered either by an external signal or by a selectable state transition of its toggle
latch T3OTL.
相關PDF資料
PDF描述
SAK-C164SV-2RF 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP64
SAF-C164SV-2RF 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP64
SAF-C164SV-2R25F 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP64
SAK-C167CS-4R40M-BA 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP144
SAK-C167CS-4RC 16-BIT, MROM, 33 MHz, MICROCONTROLLER, UUC146
相關代理商/技術參數
參數描述
SAKC164CI8EMCBXT 制造商:Infineon Technologies AG 功能描述:MCU 16-Bit C166 CISC/RISC 64KB EPROM 5V 80-Pin MQFP T/R
SAKC164CI8EMDB 制造商:Infineon Technologies AG 功能描述:
SAKC164CI8EMDB/TR 制造商:Infineon Technologies AG 功能描述:
SAKC164CI8EMDBX 制造商:Infineon Technologies AG 功能描述:MCU 16-bit C166 CISC/RISC 64KB EPROM 5V 80-Pin MQFP
SAKC164CI8EMDBXT 制造商:Infineon Technologies AG 功能描述:MCU 16-Bit C166 CISC/RISC 64KB EPROM 5V 80-Pin MQFP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*