- 您現在的位置：買賣IC網 > PDF目錄98076 > SAK-C164CI-8EMCB (INFINEON TECHNOLOGIES AG) 16-BIT, OTPROM, 20 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | SAK-C164CI-8EMCB |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, OTPROM, 20 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | 0.65 MM PITCH, METRIC, PLASTIC, QFP-80 |
| 文件頁數： | 6/80頁 |
| 文件大?。?/td> | 1337K |
| 代理商： | SAK-C164CI-8EMCB |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁
C164CI/SI
C164CL/SL
Data Sheet
9
V2.0, 2001-05
XTAL2
XTAL1
54
55
O
I
XTAL2:
Output of the oscillator amplifier circuit.
XTAL1:
Input to the oscillator amplifier and input to
the internal clock generator
To clock the device from an external source, drive XTAL1,
while leaving XTAL2 unconnected. Minimum and maximum
high/low and rise/fall times specified in the AC
Characteristics must be observed.
RSTIN
69
I/O
Reset Input with Schmitt-Trigger characteristics. A low level
at this pin while the oscillator is running resets the C164CI.
An internal pullup resistor permits power-on reset using only
a capacitor connected to
VSS.
A spike filter suppresses input pulses <10 ns. Input pulses
>100 ns safely pass the filter. The minimum duration for a
safe recognition should be 100 ns + 2 CPU clock cycles.
In bidirectional reset mode (enabled by setting bit BDRSTEN
in register SYSCON) the RSTIN line is internally pulled low
for the duration of the internal reset sequence upon any reset
(HW, SW, WDT). See note below this table.
RST
OUT
70
O
Internal Reset Indication Output. This pin is set to a low level
when the part is executing either a hardware-, a software- or
a watchdog timer reset. RSTOUT remains low until the EINIT
(end of initialization) instruction is executed.
NMI
71
I
Non-Maskable Interrupt Input. A high to low transition at this
pin causes the CPU to vector to the NMI trap routine. When
the PWRDN (power down) instruction is executed, the NMI
pin must be low in order to force the C164CI to go into power
down mode. If NMI is high, when PWRDN is executed, the
part will continue to run in normal mode.
If not used, pin NMI should be pulled high externally.
Table 2
Pin Definitions and Functions (cont’d)
Symbol Pin
No.
Input
Outp.
Function
相關PDF資料 |
PDF描述 |
|---|---|
| SAK-C164SV-2RF | 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP64 |
| SAF-C164SV-2RF | 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP64 |
| SAF-C164SV-2R25F | 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP64 |
| SAK-C167CS-4R40M-BA | 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP144 |
| SAK-C167CS-4RC | 16-BIT, MROM, 33 MHz, MICROCONTROLLER, UUC146 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAKC164CI8EMCBXT | 制造商:Infineon Technologies AG 功能描述:MCU 16-Bit C166 CISC/RISC 64KB EPROM 5V 80-Pin MQFP T/R |
| SAKC164CI8EMDB | 制造商:Infineon Technologies AG 功能描述: |
| SAKC164CI8EMDB/TR | 制造商:Infineon Technologies AG 功能描述: |
| SAKC164CI8EMDBX | 制造商:Infineon Technologies AG 功能描述:MCU 16-bit C166 CISC/RISC 64KB EPROM 5V 80-Pin MQFP |
| SAKC164CI8EMDBXT | 制造商:Infineon Technologies AG 功能描述:MCU 16-Bit C166 CISC/RISC 64KB EPROM 5V 80-Pin MQFP |
發布緊急采購，3分鐘左右您將得到回復。