參數資料
型號: SAK-C164SV-2RF
廠商: INFINEON TECHNOLOGIES AG
元件分類: 微控制器/微處理器
英文描述: 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP64
封裝: PLASTIC, TQFP-64
文件頁數: 22/65頁
文件大小: 932K
代理商: SAK-C164SV-2RF
C164SV
Data Sheet
25
V1.0, 2003-04
Preliminary
A/D Converter
For analog signal measurement, a 10-bit/12-bit A/D converter with 8 multiplexed input
channels and a sample and hold circuit has been integrated on-chip. It uses the method
of successive approximation. The sample time (for loading the capacitors) and the
conversion time is programmable and can so be adjusted to the external circuitry.
Overrun error detection/protection is provided for the conversion result register
(ADDAT): either an interrupt request will be generated when the result of a previous
conversion has not been read from the result register at the time the next conversion is
complete, or the next conversion is suspended in such a case until the previous result
has been read.
For applications which require less than 8 analog input channels, the remaining channel
inputs can be used as digital input port pins.
The A/D converter of the C164SV supports four different conversion modes. In the
standard Single Channel conversion mode, the analog level on a specified channel is
sampled once and converted to a digital result. In the Single Channel Continuous mode,
the analog level on a specified channel is repeatedly sampled and converted without
software intervention. In the Auto Scan mode, the analog levels on a prespecified
number of channels (standard or extension) are sequentially sampled and converted. In
the Auto Scan Continuous mode, the number of prespecified channels is repeatedly
sampled and converted. In addition, the conversion of a specific channel can be inserted
(injected) into a running sequence without disturbing this sequence. This is called
Channel Injection Mode.
The Peripheral Event Controller (PEC) may be used to automatically store the
conversion results into a table in memory for later evaluation, without requiring the
overhead of entering and exiting interrupt routines for each data transfer.
After each reset and also during normal operation the ADC automatically performs
calibration cycles. This automatic self-calibration constantly adjusts the converter to
changing operating conditions (e.g. temperature) and compensates process variations.
These calibration cycles are part of the conversion cycle, so they do not affect the normal
operation of the A/D converter.
In order to decouple analog inputs from digital noise and to avoid input trigger noise
those pins used for analog input can be disconnected from the digital IO or input stages
under software control. This can be selected for each pin separately via register P5DIDIS
(Port 5 Digital Input Disable).
相關PDF資料
PDF描述
SAF-C164SV-2RF 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP64
SAF-C164SV-2R25F 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP64
SAK-C167CS-4R40M-BA 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP144
SAK-C167CS-4RC 16-BIT, MROM, 33 MHz, MICROCONTROLLER, UUC146
SAK-C167CS-LC 16-BIT, MROM, 33 MHz, MICROCONTROLLER, UUC146
相關代理商/技術參數
參數描述
SAK-C167CR-16R33M 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:16-Bit Single-Chip Microcontroller
SAK-C167CR-16RM 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:16-Bit Single-Chip Microcontroller
SAK-C167CR-16RM HA+ 功能描述:16位微控制器 - MCU 16-Bit Single-Chip Microcontroller RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
SAK-C167CR-4R33M 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:16-Bit Single-Chip Microcontroller
SAK-C167CR-4RM 制造商:Rochester Electronics LLC 功能描述:- Bulk