參數資料
型號： SAK-C167CS-4R40M-BA
廠商： INFINEON TECHNOLOGIES AG
元件分類： 微控制器/微處理器
英文描述： 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP144
封裝： METRIC, PLASTIC, QFP-144
文件頁數： 16/72頁
文件大小： 1254K
代理商： SAK-C167CS-4R40M-BA
C167CS-4R
C167CS-L
Data Sheet
19
V2.2, 2001-08
Interrupt System
With an interrupt response time within a range from just 5 to 12 CPU clocks (in case of
internal program execution), the C167CS is capable of reacting very fast to the
occurrence of non-deterministic events.
The architecture of the C167CS supports several mechanisms for fast and flexible
response to service requests that can be generated from various sources internal or
external to the microcontroller. Any of these interrupt requests can be programmed to
being serviced by the Interrupt Controller or by the Peripheral Event Controller (PEC).
In contrast to a standard interrupt service where the current program execution is
suspended and a branch to the interrupt vector table is performed, just one cycle is
‘stolen’ from the current CPU activity to perform a PEC service. A PEC service implies a
single byte or word data transfer between any two memory locations with an additional
increment of either the PEC source or the destination pointer. An individual PEC transfer
counter is implicitly decremented for each PEC service except when performing in the
continuous transfer mode. When this counter reaches zero, a standard interrupt is
performed to the corresponding source related vector location. PEC services are very
well suited, for example, for supporting the transmission or reception of blocks of data.
The C167CS has 8 PEC channels each of which offers such fast interrupt-driven data
transfer capabilities.
A separate control register which contains an interrupt request flag, an interrupt enable
flag and an interrupt priority bitfield exists for each of the possible interrupt sources. Via
its related register, each source can be programmed to one of sixteen interrupt priority
levels. Once having been accepted by the CPU, an interrupt service can only be
interrupted by a higher prioritized service request. For the standard interrupt processing,
each of the possible interrupt sources has a dedicated vector location.
Fast external interrupt inputs are provided to service external interrupts with high
precision requirements. These fast interrupt inputs feature programmable edge
detection (rising edge, falling edge or both edges).
Software interrupts are supported by means of the ‘TRAP’ instruction in combination with
an individual trap (interrupt) number.
Table 3 shows all of the possible C167CS interrupt sources and the corresponding
hardware-related interrupt flags, vectors, vector locations and trap (interrupt) numbers.
Note: Interrupt nodes which are not used by associated peripherals, may be used to
generate software controlled interrupt requests by setting the respective interrupt
request bit (xIR).
相關PDF資料
PDF描述
SAK-C167CS-4RC 16-BIT, MROM, 33 MHz, MICROCONTROLLER, UUC146
SAK-C167CS-LC 16-BIT, MROM, 33 MHz, MICROCONTROLLER, UUC146
SAL-C167CS-L33C 16-BIT, MROM, 33 MHz, MICROCONTROLLER, UUC146
SAK-C504-L40M 8-BIT, 20 MHz, MICROCONTROLLER, PQFP44
SAK-C509-LM 8-BIT, 16 MHz, MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
SAK-C167CS-4RM 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:16-Bit Single-Chip Microcontroller
SAK-C167CS-L33M 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Infineon Technologies AG 功能描述:
SAK-C167CS-L33M CA+ 功能描述:16位微控制器 - MCU 16BIT SNGL CHIP 5V 33MHz ROM less RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
SAK-C167CS-L33M-CA 制造商:Infineon Technologies AG 功能描述:
SAKC167CSL33MCA+ 制造商:Infineon Technologies AG 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*