參數資料
型號： SC16C2550IB48,151
廠商： NXP Semiconductors
文件頁數： 11/46頁
文件大小： 0K
描述： IC UART DUAL W/FIFO 48-LQFP
標準包裝： 250
特點： 2 通道
通道數： 2，DUART
FIFO's： 16 字節
電源電壓： 2.5V，3.3V，5V
帶自動流量控制功能： 是
帶IrDA 編碼器/解碼器： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 48-LQFP
供應商設備封裝： 48-LQFP（7x7）
包裝： 托盤
其它名稱： 568-3261
935270020151
SC16C2550IB48-S
Philips Semiconductors
SC16C2550
Dual UART with 16 bytes of transmit and receive FIFOs and IrDA
encoder/decoder
Product data
Rev. 03 — 19 June 2003
19 of 46
9397 750 11621
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
7.2.2
IER versus Receive/Transmit FIFO polled mode operation
When FCR[0] = logic 1, resetting IER[0-3] enables the SC16C2550 in the FIFO
polled mode of operation. In this mode, interrupts are not generated and the user
must poll the LSR register for TX and/or RX data status. Since the receiver and
transmitter have separate bits in the LSR either or both can be used in the polled
mode by selecting respective transmit or receive control bit(s).
LSR[0] will be a logic 1 as long as there is one byte in the receive FIFO.
LSR[1-4] will provide the type of receive errors, or a receive break, if encountered.
LSR[5] will indicate when the transmit FIFO is empty.
LSR[6] will indicate when both the transmit FIFO and transmit shift register are
empty.
LSR[7] will show if any FIFO data errors occurred.
7.3 FIFO Control Register (FCR)
This register is used to enable the FIFOs, clear the FIFOs, set the receive FIFO
trigger levels, and select the DMA mode.
7.3.1
DMA mode
Mode 0 (FCR bit 3 = 0): Set and enable the interrupt for each single transmit or
receive operation, and is similar to the 16C450 mode. Transmit Ready (TXRDY) on
PLCC44 and LQFP48 packages will go to a logic 0 whenever the FIFO (THR, if FIFO
is not enabled) is empty. Receive Ready (RXRDY) on PLCC44 and LQFP48
packages will go to a logic 0 whenever the Receive Holding Register (RHR) is loaded
with a character.
Mode 1 (FCR bit 3 = 1): Set and enable the interrupt in a block mode operation. The
transmit interrupt is set when the transmit FIFO is empty. TXRDY on PLCC and
LQFP48 packages remains a logic 0 as long as one empty FIFO location is available.
The receive interrupt is set when the receive FIFO lls to the programmed trigger
level. However, the FIFO continues to ll regardless of the programmed level until the
FIFO is full. RXRDY on PLCC44 and LQFP48 packages transitions LOW when the
FIFO reaches the trigger level, and transitions HIGH when the FIFO empties.
相關PDF資料
PDF描述
SC16C2552BIA44,529 IC UART DUAL W/FIFO 44-PLCC
SC16C550BIB48,157 IC UART SINGLE W/FIFO 48-LQFP
SC16C554DBIA68,529 IC UART QUAD W/FIFO 68-PLCC
SC16C554IB80,528 IC UART QUAD SOT315-1
SC16C650BIB48,151 IC UART SINGLE W/FIFO 48-LQFP
相關代理商/技術參數
參數描述
SC16C2550IN40 制造商:PHILIP 功能描述:
SC16C2550IN40,112 功能描述:IC UART DUAL W/FIFO 40-DIP RoHS:是 類別:集成電路 (IC) >> 接口 - UART（通用異步接收器/發送器） 系列:- 標準包裝:250 系列:- 特點:* 通道數:2，DUART FIFO's:16 字節 規程:RS232，RS485 電源電壓:2.25 V ~ 5.5 V 帶并行端口:- 帶自動流量控制功能:是 帶IrDA 編碼器/解碼器:是 帶故障啟動位檢測功能:是 帶調制解調器控制功能:是 帶CMOS:是 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:托盤 其它名稱:XR16L2551IM-F-ND
SC16C2552 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual UART with 16-byte transmit and receive FIFOs
SC16C2552B 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
SC16C2552BIA44 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*