- 您現在的位置：買賣IC網 > PDF目錄11815 > SC16C554IB64,157 (NXP Semiconductors)IC UART QUAD W/FIFO 64-LQFP PDF資料下載
參數資料
| 型號： | SC16C554IB64,157 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 9/55頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART QUAD W/FIFO 64-LQFP |
| 標準包裝： | 800 |
| 通道數： | 4，QUART |
| FIFO's： | 16 字節 |
| 電源電壓： | 2.5V，3.3V，5V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-LQFP（10x10） |
| 包裝： | 托盤 |
| 其它名稱： | 568-1321 935270074157 SC16C554IB64 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
Philips Semiconductors
SC16C554/554D
Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder
Product data
Rev. 05 — 10 May 2004
17 of 55
9397 750 13132
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
characters as soon as received data passes the programmed trigger level. To clear
this condition, the SC16C554/554D will transmit the programmed Xon1,2 characters
as soon as receive data drops below the programmed trigger level.
6.8 Special feature software ow control
A special feature is provided to detect an 8-bit character when EFR[5] is set. When
8-bit character is detected, it will be placed on the user-accessible data stack along
with normal incoming RX data. This condition is selected in conjunction with
EFR[0-3]. Note that software ow control should be turned off when using this special
mode by setting EFR[0-3] to a logic 0.
The SC16C554/554D compares each incoming receive character with Xoff2 data. If a
match exists, the received data will be transferred to the FIFO, and ISR[4] will be set
to indicate detection of a special character. Although the Internal Register Table
(Table 8) shows each X-Register with eight bits of character information, the actual
number of bits is dependent on the programmed word length. Line Control Register
bits LCR[0-1] dene the number of character bits, i.e., either 5 bits, 6 bits, 7 bits or
8 bits. The word length selected by LCR[0-1] also determine the number of bits that
will be used for the special character comparison. Bit 0 in the X-registers corresponds
with the LSB bit for the receive character.
6.9 Hardware/software and time-out interrupts
Three special interrupts have been added to monitor the hardware and software ow
control. The interrupts are enabled by IER[5-7]. Care must be taken when handling
these interrupts. Following a reset, if the transmitter interrupt is enabled, the
SC16C554/554D will issue an interrupt to indicate that the Transmit Holding Register
is empty. This interrupt must be serviced prior to continuing operations. The LSR
register provides the current singular highest priority interrupt only. It could be noted
that CTS and RTS interrupts have lowest interrupt priority. A condition can exist
where a higher priority interrupt may mask the lower priority CTS/RTS interrupt(s).
Only after servicing the higher pending interrupt will the lower priority CTS/TRS
interrupt(s) be reected in the status register. Servicing the interrupt without
investigating further interrupt conditions can result in data errors.
When two interrupt conditions have the same priority, it is important to service these
interrupts correctly. Receive Data Ready and Receive Time Out have the same
interrupt priority (when enabled by IER[0]). The receiver issues an interrupt after the
number of characters have reached the programmed trigger level. In this case, the
SC16C554/554D FIFO may hold more characters than the programmed trigger level.
Following the removal of a data byte, the user should re-check LSR[0] for additional
characters. A Receive Time Out will not occur if the receive FIFO is empty. The
time-out counter is reset at the center of each stop bit received or each time the
receive holding register (RHR) is read. The actual time-out value is 4 character time.
In the 16 mode for the PLCC68 package, the system/board designer can optionally
provide software controlled 3-State interrupt operation. This is accomplished by
INTSEL and MCR[3]. When INTSEL interface pin is left open or made a logic 0,
MCR[3] controls the 3-State interrupt outputs, INTA-INTD. When INTSEL is a logic 1,
MCR[3] has no effect on the INTA-INTD outputs, and the package operates with
interrupt outputs enabled continuously.
相關PDF資料 |
PDF描述 |
|---|---|
| V24C24H150B3 | CONVERTER MOD DC/DC 24V 150W |
| ATMEGA644V-10MUR | MCU AVR 64K FLASH 10MHZ 44QFN |
| SC28C94A1N,112 | IC UART QUAD W/FIFO 48-DIP |
| V24C24H150B | CONVERTER MOD DC/DC 24V 150W |
| SC16C554DIA68,512 | IC UART QUAD W/FIFO 68-PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C554IB80 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder |
| SC16C554IB80,528 | 功能描述:UART 接口集成電路 Quad UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C554IB80,551 | 功能描述:UART 接口集成電路 16C 2.5V-5V 4CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C554IB80,557 | 功能描述:UART 接口集成電路 16C 2.5V-5V 4CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C650A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Asynchronous Receiver/Transmitter (UART) with 32-byte FIFO and infrared (IrDA) encoder/decoder |
發布緊急采購，3分鐘左右您將得到回復。