- 您現在的位置：買賣IC網 > PDF目錄1967 > SC16C554IB80,528 (NXP Semiconductors)IC UART QUAD SOT315-1 PDF資料下載
參數資料
| 型號： | SC16C554IB80,528 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 2/55頁 |
| 文件大小： | 0K |
| 描述： | IC UART QUAD SOT315-1 |
| 標準包裝： | 1 |
| 通道數： | 4，QUART |
| FIFO's： | 16 字節 |
| 電源電壓： | 2.5V，3.3V，5V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 80-LQFP |
| 供應商設備封裝： | 80-LQFP（12x12） |
| 包裝： | 標準包裝 |
| 其它名稱： | 568-5954-6 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
Philips Semiconductors
SC16C554/554D
Quad UART with 16-byte FIFO and infrared (IrDA) encoder/decoder
Product data
Rev. 05 — 10 May 2004
10 of 55
9397 750 13132
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
D0-D2,
D3-D7
66-68,
1-5
53-55,
56-60
7-9,
11-15
I/O
Data bus (bi-directional). These pins are the 8-bit, 3-State data bus
for transferring information to or from the controlling CPU. D0 is the
least signicant bit and the rst data bit in a transmit or receive serial
data stream.
DSRA,
DSRB,
DSRC, DSRD
10, 26,
44, 60
1, 17,
32, 48
22, 39,
62, 79
I
Data Set Ready (Active-LOW). These inputs are associated with
individual UART channels, A through D. A logic 0 on this pin indicates
the modem or data set is powered-on and is ready for data exchange
with the UART. This pin has no effect on the UART’s transmit or
receive operation.
DTRA,
DTRB,
DTRC, DTRD
12, 24,
46, 58
3, 15,
34, 46
24, 37,
64, 77
O
Data Terminal Ready (Active-LOW). These outputs are associated
with individual UART channels, A through D. A logic 0 on this pin
indicates that the SC16C554/554D is powered-on and ready. This pin
can be controlled via the modem control register. Writing a logic 1 to
MCR[0] will set the DTR output to logic 0, enabling the modem. This
pin will be a logic 1 after writing a logic 0 to MCR[0], or after a reset.
This pin has no effect on the UART’s transmit or receive operation.
GND
6, 23,
40, 57
14, 28,
45, 61
16, 36,
56, 76
I
Signal and power ground.
INTA, INTB,
INTC, INTD
15, 21,
49, 55
6, 12,
37, 43
27, 34,
67, 74
O
Interrupt A, B, C, D (Active-HIGH). This function is associated with
the 16 mode only. These pins provide individual channel interrupts
INTA-INTD. INTA-INTD are enabled when MCR[3] is set to a logic 1,
interrupts are enabled in the interrupt enable register (IER), and
when an interrupt condition exists. Interrupt conditions include:
receiver errors, available receiver buffer data, transmit buffer empty,
or when a modem status ag is detected. When the 68 mode is
selected, the functions of these pins are re-assigned. 68 mode
functions are described under their respective name/pin headings.
INTSEL
65
-
6
I
Interrupt Select (Active-HIGH, with internal pull-down). This
function is associated with the 16 mode only. When the 16 mode is
selected, this pin can be used in conjunction with MCR[3] to enable
or disable the 3-State interrupts, INTA-INTD, or override MCR[3] and
force continuous interrupts. Interrupt outputs are enabled
continuously by making this pin a logic 1. Making this pin a logic 0
allows MCR[3] to control the 3-State interrupt output. In this mode,
MCR[3] is set to a logic 1 to enable the 3-State outputs. This pin is
disabled in the 68 mode. Due to pin limitations on the 64-pin
packages, this pin is not available. To cover this limitation, the
SC16C654DIB64 version operates in the continuous interrupt enable
mode by bonding this pin to VCC internally. The SC16C654IB64
operates with MCR[3] control by bonding this pin to GND.
IOR
52
40
70
I
Input/Output Read strobe (Active-LOW). This function is
associated with the 16 mode only. A logic 0 transition on this pin will
load the contents of an internal register dened by address bits
A0-A2 onto the SC16C554/554D data bus (D0-D7) for access by
external CPU. This pin is disabled in the 68 mode.
Table 2:
Pin description…continued
Symbol
Pin
Type
Description
PLCC68 LQFP64 LQFP80
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C650BIB48,151 | IC UART SINGLE W/FIFO 48-LQFP |
| SC16C652BIB48,157 | IC ENCODER/DECODER IRDA 48LQFP |
| SC16C654BIBS,557 | IC QUAD UART 64BYTE 48HVQFN |
| SC16C750BIB64,151 | IC UART SINGLE W/FIFO 64-LQFP |
| SC16C752BIBS,157 | IC DUAL UART 64BYTE 32HVQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C650A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Asynchronous Receiver/Transmitter (UART) with 32-byte FIFO and infrared (IrDA) encoder/decoder |
| SC16C650AIA44 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Asynchronous Receiver/Transmitter (UART) with 32-byte FIFO and infrared (IrDA) encoder/decoder |
| SC16C650AIA44,512 | 功能描述:UART 接口集成電路 16C 2.5V-5V 1CH UART 32B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C650AIA44,518 | 功能描述:UART 接口集成電路 16C 2.5V-5V 1CH UART 32B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C650AIA44,529 | 功能描述:UART 接口集成電路 16C 2.5V-5V 1CH UART 32B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。