- 您現在的位置：買賣IC網 > PDF目錄3764 > SC16C650BIB48,128 (NXP Semiconductors)IC UART SOT313-2 PDF資料下載
參數資料
| 型號： | SC16C650BIB48,128 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 46/48頁 |
| 文件大小： | 0K |
| 描述： | IC UART SOT313-2 |
| 標準包裝： | 2,000 |
| 通道數： | 1，UART |
| FIFO's： | 32 字節 |
| 電源電壓： | 2.5V，3.3V，5V |
| 帶自動流量控制功能： | 是 |
| 帶IrDA 編碼器/解碼器： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | 935274391128 SC16C650BIB48-F SC16C650BIB48-F-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁
SC16C650B_4
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 04 — 14 September 2009
7 of 48
NXP Semiconductors
SC16C650B
UART with 32-byte FIFOs and IrDA encoder/decoder
RESET
39
35
24
I
Master Reset. When active (HIGH), MR clears most UART
registers and sets the levels of various output signals.
RI
43
41
-
I
Ring indicator. RI is a modem status signal. Its condition can be
checked by reading MSR[6] (RI). MSR[2] (
RI) indicates that RI has
changed from a LOW to a HIGH level since the last read from the
MSR. If the modem status interrupt is enabled when this transition
occurs, an interrupt is generated.
RTS
36
32
21
O
Request to send. When active, RTS informs the modem or data
set that the UART is ready to receive data. RTS is set to the active
level by setting the RTS modem control register bit and is set to the
inactive (HIGH) level either as a result of a Master Reset or during
loopback mode operations or by clearing bit 1 (RTS) of the MCR. In
the auto-RTS mode, RTS is set to the inactive level by the receiver
threshold control logic.
RXRDY32
29
19
O
Receiver ready. Receiver direct memory access (DMA) signaling is
available with RXRDY. When operating in the FIFO mode, one of
two types of DMA signaling can be selected using the FIFO Control
Register bit 3 (FCR[3]). When operating in the 16C450 mode, only
DMA mode 0 is allowed. Mode 0 supports single-transfer DMA in
which a transfer is made between CPU bus cycles. Mode 1
supports multi-transfer DMA in which multiple transfers are made
continuously until the receiver FIFO has been emptied. In DMA
mode 0 (FCR[0] = 0 or FCR[0] = 1, FCR[3] = 0), when there is at
least one character in the receiver FIFO or Receive Holding
Register, RXRDY is active (LOW). When RXRDY has been active
but there are no characters in the FIFO or holding register, RXRDY
goes inactive (HIGH). In DMA mode 1 (FCR[0] = 1, FCR[3] = 1),
when the trigger level or the time-out has been reached, RXRDY
goes active (LOW); when it has been active but there are no more
characters in the FIFO or holding register, it goes inactive (HIGH).
RX
11
7
5
I
Serial data input. RX is serial data input from a connected
communications device.
TX
13
8
6
O
Serial data output. TX is composite serial data output to a
connected communication device. TX is set to the marking (HIGH)
level as a result of Master Reset.
TXRDY27
23
15
O
Transmitter ready. Transmitter DMA signaling is available with
TXRDY. When operating in the FIFO mode, one of two types of
DMA signaling can be selected using FCR[3]. When operating in
the 16C450 mode, only DMA mode 0 is allowed. Mode 0 supports
single-transfer DMA in which a transfer is made between CPU bus
cycles. Mode 1 supports multi-transfer DMA in which multiple
transfers are made continuously until the transmit FIFO has been
lled.
VCC
44
42
27
power
2.5 V, 3 V or 5 V supply voltage.
GND
22
18
power
Ground voltage.
IOW
21
17
-
I
Write inputs. When either IOW or IOW is active (LOW or HIGH,
respectively) and while the UART is selected, the CPU is allowed to
write control words or data into a selected UART register. Only one
of these inputs is required to transfer data during a write operation;
the other input should be tied to its inactive level (i.e., IOW tied LOW
or IOW tied HIGH).
IOW20
16
11
I
Table 2.
Pin description …continued
Symbol
Pin
Type
Description
PLCC44
LQFP48 HVQFN32
相關PDF資料 |
PDF描述 |
|---|---|
| AT32UC3L016-ZAUR | IC MCU AVR32 16K FLASH 48VQFN |
| ATMEGA88-15MZ | MCU AVR 8K FLASH 15MHZ 32-QFN |
| ATMEGA168P-20MQR | MCU AVR 16K FLASH 20MHZ 32-QFN |
| ATMEGA164A-MCHR | IC MCU AVR 16K 20MHZ 44QFN |
| SC16C2550BIBS,151 | IC UART DUAL W/FIFO 32-HVQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C650BIB48-F | 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH UART 32B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C650BIBS | 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH UART 32B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C650BIBS,128 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C650BIBS,151 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C650BIBS,157 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。