參數資料
型號: SC16C654DBIB64,151
廠商: NXP Semiconductors
文件頁數: 44/58頁
文件大?。?/td> 0K
描述: IC UART QUAD W/FIFO 64-LQFP
產品培訓模塊: Stand-Alone UARTs
標準包裝: 160
通道數: 4,QUART
FIFO's: 64 字節
電源電壓: 2.5V,3.3V,5V
帶自動流量控制功能:
帶IrDA 編碼器/解碼器:
帶故障啟動位檢測功能:
帶調制解調器控制功能:
帶CMOS:
安裝類型: 表面貼裝
封裝/外殼: 64-LQFP
供應商設備封裝: 64-LQFP(10x10)
包裝: 托盤
產品目錄頁面: 828 (CN2011-ZH PDF)
其它名稱: 568-2048
935276671151
SC16C654DBIB64-S
49
7674F–AVR–09/09
ATmega164P/324P/644P
9.
System Control and Reset
9.0.1
Resetting the AVR
During reset, all I/O Registers are set to their initial values, and the program starts execution
from the Reset Vector. The instruction placed at the Reset Vector must be a JMP – Absolute
Jump – instruction to the reset handling routine. If the program never enables an interrupt
source, the Interrupt Vectors are not used, and regular program code can be placed at these
locations. This is also the case if the Reset Vector is in the Application section while the Interrupt
Vectors are in the Boot section or vice versa. The circuit diagram in Figure 9-1 on page 50
shows the reset logic. “System and Reset Characteristics” on page 332 defines the electrical
parameters of the reset circuitry.
The I/O ports of the AVR are immediately reset to their initial state when a reset source goes
active. This does not require any clock source to be running.
After all reset sources have gone inactive, a delay counter is invoked, stretching the internal
reset. This allows the power to reach a stable level before normal operation starts. The time-out
period of the delay counter is defined by the user through the SUT and CKSEL Fuses. The dif-
ferent selections for the delay period are presented in “Clock Sources” on page 30.
9.0.2
Reset Sources
The ATmega164P/324P/644P has five sources of reset:
Power-on Reset. The MCU is reset when the supply voltage is below the Power-on Reset
threshold (V
POT).
External Reset. The MCU is reset when a low level is present on the RESET pin for longer than
the minimum pulse length.
Watchdog Reset. The MCU is reset when the Watchdog Timer period expires and the
Watchdog is enabled.
Brown-out Reset. The MCU is reset when the supply voltage V
CC is below the Brown-out Reset
threshold (V
BOT) and the Brown-out Detector is enabled.
JTAG AVR Reset. The MCU is reset as long as there is a logic one in the Reset Register, one
of the scan chains of the JTAG system. Refer to the section “IEEE 1149.1 (JTAG)
相關PDF資料
PDF描述
ATMEGA164PA-MUR MCU AVR 16KB FLASH 20MHZ 44QFN
SC16C754BIBM,151 IC UART QUAD W/FIFO 64-LQFP
SC16C654BIBM,151 IC UART QUAD W/FIFO 64-LQFP
ATMEGA164A-CUR IC MCU AVR 16K 20MHZ 49VFBGA
SC16C554DBIB64,157 IC UART QUAD W/FIFO 64-LQFP
相關代理商/技術參數
參數描述
SC16C654DBIB64-F 功能描述:UART 接口集成電路 16CB 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C654DIB64 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Quad UART with 64-byte FIFO and infrared (IrDA) encoder/decoder
SC16C654DIB64,128 功能描述:UART 接口集成電路 16C 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C654DIB64,151 功能描述:UART 接口集成電路 16C 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C654DIB64,157 功能描述:UART 接口集成電路 16C 2.5V-5V 4CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel