參數資料
型號： SC16C750BIB64,157
廠商： NXP Semiconductors
文件頁數： 16/44頁
文件大小： 0K
描述： IC UART 64BYTE 64LQFP
標準包裝： 800
通道數： 1，UART
FIFO's： 64 字節
電源電壓： 2.5V，3.3V，5V
帶自動流量控制功能： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 64-LQFP
供應商設備封裝： 64-LQFP（10x10）
包裝： 托盤
其它名稱： 935274403157
SC16C750BIB64
SC16C750BIB64-ND
SC16C750B_5
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 05 — 17 October 2008
23 of 44
NXP Semiconductors
SC16C750B
5 V, 3.3 V and 2.5 V UART with 64-byte FIFOs
7.6 Modem Control Register (MCR)
This register controls the interface with the modem or a peripheral device.
The ow control can be congured by programming MCR[1] and MCR[5] as shown in
Table 18.
Modem Control Register bits description
Bit
Symbol
Description
7
MCR[7]
reserved; set to 0
6
MCR[6]
reserved; set to 0
5
MCR[5]
AFE. This bit is the auto ow control enable. When this bit is set, the auto
ow control is enabled.
4
MCR[4]
Loopback. Enable the local Loopback mode (diagnostics). In this mode the
transmitter output (TX) and the receiver input (RX), CTS, DSR, DCD, and RI
are disconnected from the SC16C750B I/O pins. Internally the modem data
and control pins are connected into a loopback data conguration (see
Figure 6). In this mode, the receiver and transmitter interrupts remain fully
operational. The Modem Control Interrupts are also operational, but the
interrupts’ sources are switched to the lower four bits of the Modem Control.
Interrupts continue to be controlled by the IER register.
logic 0 = disable Loopback mode (normal default condition)
logic 1 = enable local Loopback mode (diagnostics)
3
MCR[3]
OUT2, INT enable. Used to control the modem DCD signal in the Loopback
mode.
logic 0 = set OUT2 to HIGH. In the Loopback mode, sets OUT2 (DCD)
internally to a logic 1.
logic 1 = set OUT2 to LOW. In the Loopback mode, sets OUT2 (DCD)
internally to a logic 0.
2
MCR[2]
OUT1. This bit is used in the Loopback mode only. In the Loopback mode,
this bit is used to write the state of the modem RI interface signal via OUT1.
1
MCR[1]
RTS
logic 0 = force RTS output to a logic 1 (normal default condition)
logic 1 = force RTS output to a logic 0
0
MCR[0]
DTR
logic 0 = force DTR output to a logic 1 (normal default condition)
logic 1 = force DTR output to a logic 0
Table 19.
Flow control conguration
MCR[5] (AFE)
MCR[1] (RTS)
Flow conguration
1
auto RTS and CTS enabled
1
0
auto CTS only enabled
0
X
auto RTS and CTS disabled
相關PDF資料
PDF描述
ATMEGA169PV-8MUR MCU AVR 16KB FLASH 16MHZ 64QFN
D38999/24FD19PN CONN RCPT 19POS JAM NUT W/PINS
VI-2N2-IY CONVERTER MOD DC/DC 15V 50W
VE-BTN-IX-F4 CONVERTER MOD DC/DC 18.5V 75W
MS3101E28-18S CONN RCPT 12POS FREE HNG W/SCKT
相關代理商/技術參數
參數描述
SC16C750BIB64-F 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C750BIB64-S 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C750BIBS 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C750BIBS,128 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C750BIBS,151 功能描述:UART 接口集成電路 1CH. UART 64B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*