- 您現在的位置：買賣IC網 > PDF目錄372122 > SC28L194 (NXP Semiconductors N.V.) Quad UART for 3.3V and 5V supply voltage(在3.3V和5V電源電壓中應用的四 UART) PDF資料下載
參數資料
| 型號： | SC28L194 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Quad UART for 3.3V and 5V supply voltage(在3.3V和5V電源電壓中應用的四 UART) |
| 中文描述： | 四UART的3.3V和5V電源電壓（在3.3和5V的電源電壓中應用的四UART）的 |
| 文件頁數： | 18/52頁 |
| 文件大小： | 294K |
| 代理商： | SC28L194 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
Philips Semiconductors
Preliminary specification
SC28L194
Quad UART for 3.3V and 5V supply voltage
1998 Sep 21
18
Table 4.
Bit 7
1 - on
áááááááááááááááááááááááááááááá
áááááááááááááááááááááááááááááá
á
á
ááááááááááááááááááááááááááááááá
MR1[7]: Receiver Request to Send Control
This bit controls the deactivation of the RTSN output (I/O2) by the
receiver. This output is asserted and negated by commands applied
via the command register. MR1[7] = 1 causes RTSN to be
automatically negated upon receipt of a valid start bit if the receiver
FIFO is 3/4 full or greater. RTSN is reasserted when an the FIFO fill
level falls below 3/4 full. This constitutes a change from previous
members of Philips (Signets)’ UART families where the RTSN
function triggered on FIFO full. This behavior caused problems with
PC UARTs that could not stop transmission at the proper time. The
RTSN feature can be used to prevent overrun in the receiver, by
using the RTSN output signal, to control the CTSN input of the
transmitting device.
á
Bit 6
Bit 5
on a character by character basis; the status applies only to the
character at. the bottom of the FIFO. In the block mode, the status
provided in the SR for these bits is the accumulation (logical OR) of
the status for all characters coming to the top of the FIFO, since the
last reset error command was issued.
Bit 4:3
á
Bit 2
á
Bit 1:0
áááááááááááááááááááááááááááááá
áááá
1 - ISR masked
1 = Block
01 - Force parity
11 - Special Mode
01 - 6
11 - 8
á
ááááá
ááááá
á
á
áááá
á
á
ááááá
ááááá
á
áááá
áááá
á
ááááá
ááááá
á
á
MR1[6]: Interrupt Status Masking
This bit controls the readout mode of the Interrupt Status Register,
ISR. If set, the ISR reads the current status masked by the IMR, i.e.
only interrupt sources enabled in the IMR can ever show a ‘1’ in the
ISR. If cleared, the ISR shows the current status of the interrupt
source without regard to the Interrupt Mask setting.
MR1[5]: Error Mode Select
This bit selects the operating mode of the three FIFOed status bits
(FE, PE, received break). In the character mode, status is provided
MR1[4:3]: Parity Mode Select
If ‘with parity’ or ’force parity’ is selected, a parity bit is added to the
transmitted character and the receiver performs a parity check on
incoming data. MR1[4:3] = 11 selects the channel to operate in the
special Wake-up mode.
MR1[2]: Parity Type Select
This bit sets the parity type (odd or even) if the ’with parity’ mode is
programmed by MR1[4:3], and the polarity of the forced parity bit if
the ’force parity’ mode is programmed. It has no effect if the ’no
parity’ mode is programmed. In the special ’Wake-up’ mode, it
selects the polarity of the A/D bit. The parity bit is used to an
address or data byte in the ’Wake-up’ mode.
MR1[1:0]: Bits per Character Select
This field selects the number of data bits per character to be
transmitted and received. This number does
not
include the start,
parity, or stop bits.
相關PDF資料 |
PDF描述 |
|---|---|
| SC28L198 | Octal UART for 3.3V and 5V supply voltage |
| SC28L198A1 | Octal UART for 3.3V and 5V supply voltage |
| SC28L198C1A | Cable Ties; Color:Black; Pack Quantity:100 |
| SC28C198A1A | Octal UART for 3.3V and 5V supply voltage |
| SC28L202A1 | Dual universal asynchronous receiver/transmitter DUART |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC28L194A1A | 功能描述:UART 接口集成電路 3V-5V 4CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC28L194A1A,512 | 功能描述:UART 接口集成電路 3V-5V 4CH UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC28L194A1A,518 | 功能描述:UART 接口集成電路 3V-5V 4CH UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC28L194A1A,529 | 功能描述:UART 接口集成電路 3V-5V 4CH UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC28L194A1A-S | 功能描述:UART 接口集成電路 3V-5V 4CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。