參數資料
型號： SC28L92A1BS,528
廠商： NXP Semiconductors
文件頁數： 50/73頁
文件大小： 0K
描述： IC UART DUAL W/FIFO 44PQFP
標準包裝： 4,000
系列： IMPACT
特點： 故障啟動位檢測
通道數： 2，DUART
FIFO's： 16 字節
電源電壓： 3.3V，5V
帶自動流量控制功能： 是
帶故障啟動位檢測功能： 是
帶調制解調器控制功能： 是
帶CMOS： 是
安裝類型： 表面貼裝
封裝/外殼： 48-VFQFN 裸露焊盤
供應商設備封裝： 48-HVQFN EP（6x6）
包裝： 帶卷 (TR)
其它名稱： 935281063528
SC28L92A1BS-F
SC28L92A1BS-F-ND
54
2552K–AVR–04/11
ATmega329/3290/649/6490
12. External Interrupts
The External Interrupts are triggered by the INT0 pin or any of the PCINT30..0 pins. Observe
that, if enabled, the interrupts will trigger even if the INT0 or PCINT30..0 pins are configured as
outputs. This feature provides a way of generating a software interrupt. The pin change interrupt
PCI1 will trigger if any enabled PCINT15..8 pin toggles. Pin change interrupts PCI0 will trigger if
any enabled PCINT7..0 pin toggles. The PCMSK3, PCMSK2, PCMSK1, and PCMSK0 Registers
control which pins contribute to the pin change interrupts. Pin change interrupts on PCINT30..0
are detected asynchronously. This implies that these interrupts can be used for waking the part
also from sleep modes other than Idle mode.
The INT0 interrupts can be triggered by a falling or rising edge or a low level. This is set up as
indicated in the specification for the External Interrupt Control Register A – EICRA. When the
INT0 interrupt is enabled and is configured as level triggered, the interrupt will trigger as long as
the pin is held low. Note that recognition of falling or rising edge interrupts on INT0 requires the
presence of an I/O clock, described in “Clock Systems and their Distribution” on page 26. Low
level interrupt on INT0 is detected asynchronously. This implies that this interrupt can be used
for waking the part also from sleep modes other than Idle mode. The I/O clock is halted in all
sleep modes except Idle mode.
Note that if a level triggered interrupt is used for wake-up from Power-down, the required level
must be held long enough for the MCU to complete the wake-up to trigger the level interrupt. If
the level disappears before the end of the Start-up Time, the MCU will still wake up, but no inter-
rupt will be generated. The start-up time is defined by the SUT and CKSEL Fuses as described
12.1
Pin Change Interrupt Timing
An example of timing of a pin change interrupt is shown in Figure 12-1.
Figure 12-1. Pin Change Interrupt
clk
PCINT(n)
pin_lat
pin_sync
pcint_in_(n)
pcint_syn
pcint_setflag
PCIF
PCINT(0)
pin_sync
pcint_syn
pin_lat
D
Q
LE
pcint_setflag
PCIF
clk
PCINT(0) in PCMSK(x)
pcint_in_(0)
0
x
相關PDF資料
PDF描述
V24B3V3H100BG2 CONVERTER MOD DC/DC 3.3V 100W
D38999/20FA98SN CONN RCPT 3POS WALL MNT W/SCKT
V24B3V3H100BG CONVERTER MOD DC/DC 3.3V 100W
SC28L92A1BS,557 IC UART DUAL W/FIFO 44PQFP
MS27467T11F99SA CONN PLUG 7POS STRAIGHT W/SCKT
相關代理商/技術參數
參數描述
SC28L92A1BS-F 功能描述:UART 接口集成電路 3V-5V 1CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC28L92A1BS-S 功能描述:UART 接口集成電路 3V-5V 1CH UART INTEL/MOT INTRF RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC28P-1GREEN 制造商:Thomas & Betts 功能描述:ID TAG GREEN
SC28P-1RED 制造商:Thomas & Betts 功能描述:ID TAG RED
SC28P-1YELLOW 制造商:Thomas & Betts 功能描述:ID TAG YELLOW
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*