- 您現在的位置：買賣IC網 > PDF目錄25623 > SCC9521002-01C (ATMEL CORP) 8-BIT, 30 MHz, MICROCONTROLLER, CDIP40 PDF資料下載
參數資料
| 型號： | SCC9521002-01C |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, 30 MHz, MICROCONTROLLER, CDIP40 |
| 封裝： | SIDE BRAZED, DIP-40 |
| 文件頁數： | 37/109頁 |
| 文件大?。?/td> | 10824K |
| 代理商： | SCC9521002-01C |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁
281
7593L–AVR–09/12
AT90USB64/128
2 - CTRLDIR - Control Direction (flag, and bit for debug purpose)
Set by hardware after a SETUP packet, and gives the direction of the following packet:
- 1 for IN endpoint
- 0 for OUT endpoint
Can not be set or cleared by software.
1-0 - CURRBK1:0 - Current Bank (all endpoints except Control endpoint) flag
Set by hardware to indicate the number of the current bank:
00b
Bank0
01b
Bank1
1xb
Reserved
Can not be set or cleared by software.
7 - FIFOCON - FIFO Control bit
For OUT and SETUP Endpoint:
Set by hardware when a new OUT message is stored in the current bank, at the same time than
RXOUT or RXSTP.
Clear to free the current bank and to switch to the following bank. Setting by software has no
effect.
For IN Endpoint:
Set by hardware when the current bank is free, at the same time than TXIN.
Clear to send the FIFO data and to switch the bank. Setting by software has no effect.
6 - NAKINI - NAK IN Received Interrupt flag
Set by hardware when a NAK handshake has been sent in response of a IN request from the
host. This triggers an USB interrupt if NAKINE is sent.
Shall be cleared by software. Setting by software has no effect.
5 - RWAL - Read/Write Allowed flag
Set by hardware to signal:
- for an IN endpoint: the current bank is not full, that is, the firmware can push data into the FIFO,
- for an OUT endpoint: the current bank is not empty, that is, the firmware can read data from the
FIFO.
The bit is never set if STALLRQ is set, or in case of error.
Cleared by hardware otherwise.
This bit shall not be used for the control endpoint.
Bit
7
6
5
43210
FIFOCON
NAKINI
RWAL
NAKOUTI
RXSTPI
RXOUTI
STALLEDI
TXINI
UEINTX
Read/write
R/W
Initial value
00
0
00000
相關PDF資料 |
PDF描述 |
|---|---|
| S80C52XXX-12D | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQCC44 |
| S80C32E-40SHXXX:RD | 8-BIT, 40 MHz, MICROCONTROLLER, PQCC44 |
| S80C52TXXX-12 | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQCC44 |
| S80C31-20D | 8-BIT, 20 MHz, MICROCONTROLLER, PQCC44 |
| S80C154-20R | 8-BIT, 20 MHz, MICROCONTROLLER, PQCC44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SCC9521002-02B | 制造商:AIMTEC 制造商全稱:AIMTEC 功能描述:Rad. Tolerant 8-bit ROMless Microcontroller |
| SCCA-1-01 | 制造商:Richco 功能描述:STANDOFF CABLE CLIP NAT 4MM SPC |
| SCCA-1-19 | 制造商:ESSENTRA COMPONENTS 功能描述:STANDOFF CABLE CLIP NAT 4MM SPC 制造商:Richco 功能描述:STANDOFF CABLE CLIP NAT 4MM SPC |
| SCCA-2-01 | 制造商:ESSENTRA COMPONENTS 功能描述:STANDOFF CABLE CLIP NAT 6MM SPC 制造商:Richco 功能描述:STANDOFF CABLE CLIP NAT 6MM SPC |
| SCCA-2-19 | 制造商:Richco 功能描述:STANDOFF CABLE CLIP NAT 6MM SPC |
發布緊急采購，3分鐘左右您將得到回復。