參數資料
型號： SCN2652AC2A44
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： NT Series Toggle Switch, 1 pole, 3 position, Solder terminal, Locking Lever
中文描述： 1 CHANNEL(S), 2M bps, MULTI PROTOCOL CONTROLLER, PQCC44
封裝： PLASTIC, LCC-44
文件頁數： 15/28頁
文件大?。?/td> 651K
代理商： SCN2652AC2A44
Philips Semiconductors
Product specification
SCN2652/SCN68652
Multi-protocol communications controller (MPCC)
1995 May 01
15
Table 7. Transmit Data/Status Register (TDSR) (R/W except TDSR15)
BIT
NAME
MODE
FUNCTION
00–07
TxDB
BOP/BCP
Transmit data buffer. Contains processor loaded characters to be serialized in TxSR and
transmitted on TxSO.
Transmitter start of message. Set by the processor to initiate message transmission provided
TxE = 1.
TSOM = 1 generates FLAGs. When TSOM = 0 transmission is from TxDB and FCS
generation (if specified) begins. FCS, as specified by PCSAR
8–10
, should be CRC–CCITT
preset to 1’s.
TSOM = 1 generates SYNCs from PCSAR
L
or transmits from TxDB for IDLE = 0 or 1
respectively. When TSOM = 0 transmission is from TxDB and CRC generation (if specified)
begins.
08
TSOM
BOP
BCP
09
TEOM
Transmit end of message. Used to terminate a transmitted message.
TEOM = 1 causes the FCS and the closing FLAG to be transmitted following the transmission
of the data character in TxSR. FLAGs are transmitted until TEOM = 0. ABORT or GA are
transmitted if TABORT or TGA are set when TEOM = 1.
TEOM = 1 causes CRC–16 to be transmitted (if selected) followed by SYNCs from PCSAR
L
or TxDB (IDLE = 0 or 1). Clearing TEOM prior to the end of CRC–16 transmission (when
TxBE = 1) causes TxSO to be marked following the CRC–16. TxE must be dropped before a
new message can be initiated. If CRC is not selected, TEOM should not be set.
BOP
BCP
10
TABORT
BOP
Transmitter abort = 1 will cause ABORT or FLAG to be sent (IDLE = 1 or 1) after the current
character is transmitted. (ABORT = 11111111)
Transmit go ahead (GA) instead of FLAG when TEOM = 1. This facilitates repeater
termination in loop mode. (GA = 01111111)
11
TGA
BOP
12–14
Not Defined
15
TERR
Read
only
Transmitter error = 1 indicates the TxDB has not been loaded in time (one character time–1/2
TxC period after TxBE is asserted) to maintain continuous transmission. TxU will be asserted
to inform the processor of this condition. TERR is cleared by setting TSOM. See timing
diagram.
ABORT’s or FLAG’s are sent as fill characters (IDLE = 0 or 1)
SYNC’s or MARK’s are sent as fill characters (IDLE = 0 or 1). For IDLE = 1 the last character
before underrun is not valid.
BOP
BCP
相關PDF資料
PDF描述
SCN2652AC2N40 Multi-protocol communications controller MPCC
SCN68652 Multi-protocol communications controller MPCC
SCN68652AC2A44 Multi-protocol communications controller MPCC
SCN68652AC2N40 Multi-protocol communications controller MPCC
SCN2652AC2F40 HEATSINK TO-220 W/SHURLOCK-CLIP
相關代理商/技術參數
參數描述
SCN2652AC2F40 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multi-protocol communications controller MPCC
SCN2652AC2N40 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multi-protocol communications controller MPCC
SCN26562 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual universal serial communications controller DUSCC
SCN26562C2A52 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Communications Controller
SCN26562C2N48 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Communications Controller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*