參數資料
型號： SCN2681AC1A44
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： RB Series - Econoline Unregulated DC-DC Converters; Input Voltage (Vdc): 12V; Output Voltage (Vdc): 3.3V; Power: 1W; Low Cost 1W Converter; Power Sharing on Dual Output Version; Industry Standard Pinout; 1kVDC & 2kVDC Isolation Options; Optional Continuous Short Circuit Protected; UL94V-0 Package Material; Efficiency to 85%
中文描述： 2 CHANNEL(S), 1M bps, SERIAL COMM CONTROLLER, PQCC44
封裝： PLASTIC, MO-047AC, SOT-187-2, LCC-44
文件頁數： 24/30頁
文件大?。?/td> 205K
代理商： SCN2681AC1A44
Philips Semiconductors
Product specification
SCN2681
Dual asynchronous receiver/transmitter (DUART)
1998 Sep 04
24
Table 5.
Baud Rates Extended
Normal BRG
BRG Test
CSR[7:4]
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
ACR[7] = 0
50
110
134.5
200
300
600
1,200
1,050
2,400
4,800
7,200
9,600
38.4K
Timer
I/O2 – 16X
I/O2 – 1X
ACR[7] = 1
75
110
134.5
150
300
600
1,200
2,000
2,400
4,800
1,800
9,600
19.2K
Timer
I/O2 – 16X
I/O2 – 1X
ACR[7] = 0
4,800
880
1,076
19.2K
28.8K
57.6K
115.2K
1,050
57.6K
4,800
57.6K
9,600
38.4K
Timer
I/O2 – 16X
I/O2 – 1X
ACR[7] = 1
7,200
880
1,076
14.4K
28.8K
57.6K
115.2K
2,000
57.6K
4,800
14.4K
9,600
19.2K
Timer
I/O2 – 16X
I/O2 – 1X
NOTE: Each read on address H‘2’ will toggle the baud rate test mode. When in the BRG test mode, the baud rates change as shown to the left.
This change affects all receivers and transmitters on the DUART. See “Extended baud rates for SCN2681, SCN68681, SCC2691, SCC2692,
SCC68681 and SCC2698B”in application notes elsewhere in this publication
The test mode at address H‘A’ changes all transmitters and receivers to the 1x mode and connects the output ports to some internal nodes.
A condition that occurs infrequently has been observed where the receiver will ignore all data. It is caused by a corruption of the start bit
generally due to noise. When this occurs the receiver will appear to be asleep or locked up. The receiver must be reset for the UART to
continue to function properly.
Reset in the Normal Mode (Receiver Enabled)
Recovery can be accomplished easily by issuing a receiver software reset followed by a receiver enable. All receiver data, status and
programming will be preserved and available before reset. The reset will NOT affect the programming.
Reset in the Wake-Up Mode (MR1[4:3] = 11)
Recovery can also be accomplished easily by first exiting the wake-up mode (MR1[4:3] = 00 or 01 or 10), then issuing a receiver software
reset followed by a wake-up re-entry (MR1[4:3] = 11). All receiver data, status and programming will be preserved and available before
reset. The reset will NOT affect the programming.
The receiver has a digital filter designed to reject “noisy” data transitions and the receiver state machine was designed to reject noisy start
bits or noise that might be considered a start bit. In spite of these precautions, corruption of the start bit can occur in 15ns window
approximately 100ns prior to the rising edge of the data clock. The probability of this occurring is less than 10
–5
at 9600 baud.
A corrupted start bit may have some deleterious effects in ASYNC operation if it occurs within a normal data block. The receiver will tend
to align its data clock to the next ‘0’ bit in the data stream, thus potentially corrupting the remainder of the data block. A good design
practice, in environments where start bit corruption is possible, is to monitor data quality (framing error, parity error, break change and
received break) and “data stopped” time out periods. Time out periods can be enabled using the counter/timer in the SCC2691, SCC2692,
SCC2698B and SC68692 products. This monitoring can indicate a potential start bit corruption problem.
SD00097
相關PDF資料
PDF描述
SCN2681 Dual asynchronous receiver/transmitter DUART
SCN2681AE1N24 Dual asynchronous receiver/transmitter DUART
SCN2681AE1N28 CCTV VIDEO BALUN
SCN2681AE1N40 Dual asynchronous receiver/transmitter DUART
SCN2681AC1N24 Dual asynchronous receiver/transmitter DUART
相關代理商/技術參數
參數描述
SCN2681AC1F40 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UART
SCN2681AC1N24 制造商:STMicroelectronics 功能描述:UART, 24 Pin, Plastic, DIP
SCN2681AC1N28 制造商:NXP Semiconductors 功能描述:
SCN2681AC1N40 制造商:NXP Semiconductors 功能描述: 制造商:NXP Semiconductors 功能描述:UART, 40 Pin, Plastic, DIP
SCN2681AE1A44 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual asynchronous receiver/transmitter DUART
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*