- 您現在的位置：買賣IC網 > PDF目錄376345 > SG1526 (Microsemi Corporation) REGULATING PULSE WIDTH MODULATOR PDF資料下載
參數資料
| 型號： | SG1526 |
| 廠商： | Microsemi Corporation |
| 英文描述： | REGULATING PULSE WIDTH MODULATOR |
| 中文描述： | 調控脈寬調制器 |
| 文件頁數： | 6/9頁 |
| 文件大?。?/td> | 182K |
| 代理商： | SG1526 |
4/90 Rev 1.1 2/94
Copyright
1994
L
IN
F
IN
ITY
Microelectronics Inc.
11861 Western Avenue
∞
∞
Garden Grove, CA 92841
(714) 898-8121
∞
FAX: (714) 893-2570
6
SG1526/SG2526/SG3526
APPLICATION INFORMATION
VOLTAGE REFERENCE
The reference regulator of the SG1526 is based on a temperature compensated
zener diode. The circuitry is fully active at supply voltages above +8 volts., and
provides up to 20mA of load current to external circuitry at +5.0 volts. In systems
where additional current is required, an external PNP transistor can be used to
boost the available current. A rugged low frequency audio-type transistor should
be used, and lead lengths between the PWM and transistor should be as short as
possible to minimize the risk of oscillations. Even so, some types of transistors
may require collector-base capacitance for stability. Up to 1amp of load current
can be obtained with excellent regulation if the device selected maintains high
current gain.
UNDERVOLTAGE LOCKOUT
The undervoltage lockout circuit protects the SG1526 and the power devices it controls from inadequate supply voltage. If
+V
is too low, the circuit disables the output drivers and holds the RESET pin LOW. This prevents spurious output pulses
while the control circuitry is stabilizing, and holds the soft-start timing capacitor in a discharged state.
The circuit consists of a +1.2 volt bandgap reference and comparator circuit which
is active when the reference voltage has risen to 3V
or 1.8 volts at 25°C. When
the reference voltage rises to approximately +4.4 volts, the circuit enables the
output drivers and releases the RESET pin, allowing a normal soft-start. The
comparator has 200mV of hysteresis to minimize oscillation at the trip point. When
+V
to the PWM is removed and the reference drops to +4.2 volts, the undervolt-
age circuit pulls RESET LOW again. The soft-start capacitor is immediately
discharged, and the PWM is ready for another soft-start cycle.
The SG1526 can operate from a +5 volt supply by connecting the V
REF
pin to the
+V
IN
pin and maintaining the supply between +4.8 and +5.2 volts.
FIGURE 18.
SIMPLIFIED UNDERVOLTAGE LOCKOUT
SOFT-START CIRCUIT
The soft-start circuit protects the power transistors and rectifier diodes from high
current surges during power supply turn-on. When supply voltage is first applied
to the SG1526, the undervoltage lockout circuit holds RESET LOW with Q3. Q1
is turned on, which holds the soft-start capacitor voltage at zero. The second
collector of Q1 clamps the output error amplifier to ground, guaranteeing zero duty
cycle at the driver outputs. When the supply voltage reaches normal operating
range, RESET will go HIGH. Q1 turns off, allowing the internal 100μA current
source to charge C
. Q2 clamps the error amplifier output to 1V
above the
voltage on C
. As the soft-start voltage ramps up to +5 volts, the duty cycle of the
PWM linearly increases to whatever value the voltage regulation loop requires for
an error null. Figure 10 gives the timing relationship between C
S
and ramp time
to 100% duty cycle.
FIGURE 19.
SOFT-START CIRCUIT SCHEMATIC
FIGURE 20.
DIGITAL CONTROL PORT SCHEMATIC
DIGITAL CONTROL PORTS
The three digital control ports of the SG1526 are bi-directional. Each pin can drive
TTL and 5 volt CMOS logic directly, up to a fan-out of 10 low-power Schottky gates.
Each pin can also be directly driven by open-collector voltage comparators; fan-
in is equivalent to 1 low-power Schottky gate. Each port is normally HIGH; the pin
is pulled LOW to activate the particular function. Driving SYNC LOW initiates a
discharge cycle in the oscillator. Pulling SHUTDOWN LOW immediately inhibits
all PWM output pulses. Holding RESET LOW discharges the soft-start capacitor.
The logic threshold is +1.1 volts at 25°C. Noise immunity can be gained at the
expense of fan-out with an external 2K pullup resistor to +5 volts.
FIGURE 17.
EXTENDING REFERENCE OUTPUT CURRENT
相關PDF資料 |
PDF描述 |
|---|---|
| SG1526J | REGULATING PULSE WIDTH MODULATOR |
| SG1526L | REGULATING PULSE WIDTH MODULATOR |
| SG2526 | REGULATING PULSE WIDTH MODULATOR |
| SG2526DW | REGULATING PULSE WIDTH MODULATOR |
| SG2526J | REGULATING PULSE WIDTH MODULATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SG1526_1 | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:REGULATING PULSE WIDTH MODULATOR |
| SG1526B | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:REGULATING PULSE WIDTH MODULATOR |
| SG1526B_1 | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:REGULATING PULSE WIDTH MODULATOR |
| SG1526BJ | 功能描述:IC REG CTRLR BUCK PWM VM 18-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 特色產品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 標準包裝:1 系列:PowerWise® PWM 型:電壓模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.5 V ~ 18 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-5°C ~ 125°C 封裝/外殼:32-WFQFN 裸露焊盤 包裝:Digi-Reel® 產品目錄頁面:1303 (CN2011-ZH PDF) 其它名稱:LM3754SQDKR |
| SG1526BJ/883B | 制造商:Microsemi Corporation 功能描述:Voltage Mode PWM Controller 100mA 18-Pin CDIP |
發布緊急采購，3分鐘左右您將得到回復。