參數資料
型號： SI2400URT-EVB
廠商： Silicon Laboratories Inc
文件頁數： 30/94頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR SI2400 ISOMODEM
標準包裝： 1
系列： ISOmodem®
主要目的： 電信，調制解調器
嵌入式： 否
已用 IC / 零件： SI2400
主要屬性： 雙路 RJ-11 連接至電話線路，音頻連接器
次要屬性： RS-232，TTL 串行和 USB 接口
已供物品： 板，調制解調器，電源
相關產品： SI2400-BS-ND - IC ISOMODEM SYSTEM-SIDE 16SOIC
SI2400-FS-ND - IC ISOMODEM SYST-SIDE DAA 16SOIC
336-1093-ND - IC ISOMODEM SYSTEM-SIDE 16SOIC
其它名稱： 336-1166
Si2400
36
Rev. 1.3
6.5.7. Intermessage Timing
Intermessage timing is accomplished in three ways,
relative to the end of the previous message (“,” result
code), relative to the Kissoff Tone (“K” result code) or
relative to the Kissoff timeout (“^” result code).
If the intermessage timing is relative to the end of the
previous message (S36[3:2] [IDKT] = 10b or 11b), the
intermessage timer begins with the “,” result code. The
Si2400 sends an “N” to mark the time in which the
intermessage timer has timed out. If another message
is received prior to the “N”, the Si2400 keeps the
message and sends it to the receiver at the time the “N”
is sent.
If a message is not received within the time frame
defined by “,” and “N”, the Si2400 sends nothing, waits
for the next message and transmits the message as
soon as the host sends the message. This message
may not be accepted by the alarm receiver.
If the intermessage timing is relative to the end of the
Kissoff Tone, the timing begins when the “K” result code
is sent. In the event a kissoff tone was not detected, the
intermessage timing begins when the “^” is sent.
6.5.8. Returning to Command Mode
To return to command mode, the host sends any
character except the “~” and “!” characters. The
example here uses a <CR> to escape.
Once in command mode, all of the AT commands are
available.
ATH<CR>
Is used to hang up the line. Note that it is
the responsibility of the host to hang up the
line.
!7xxx<CR> Sends the message xxx without dialing.
The message is sent as soon as the
Si2400 receives the <CR>. After this
message, it is again possible to send
subsequent messages using the “~” and “!”
commands shown above.
X1
Search for positive and negative acknowledge tones in
SIA half-duplex 300 bps mode. The Si2400 will respond
with “P” when a positive acknowledge is detected and
“N” when a negative acknowledge is detected.
X2
Return to online mode in SIA half-duplex mode as
transmitter.
X3
Return to online mode in SIA half-duplex mode as
receiver.
Figure 12. !7 Security Timing
S39 (CDT)
Before give up on
handshake
f = S38[1:0] (HF)
min.
2nd M essage
S36[1:0] (IT) = 0Xb
Interdigit
S36[1:0] (IT) = 1Xb
Interdigit
Handshake
Tone
Kissoff
Tone
S36[3:2] (IDKT)
Before Indicating lack
of Kissoff
1st
Digit
Last
Digit
1st
Digit
Last
Digit
S36[3:2] (IDKT) =
1Xb
Interm essage from end of previous
m essage to start of next m essage
Intradigit Tim ing
Pulse O n = S36[5:4] (PON)
Pulse O ff = S36[7:6] (POF)
Pulse freq = S38[6:5] (DCF)
S36[3:2] (IDKT) = 0Xb Interm essage
From end of Kissoff Tone
S38[7] (DBD)
S38[4:2] (HMT)
f = S38[6:5] (DCF)
S38[4:2] (HMT)
相關PDF資料
PDF描述
CM322522-1R8JL INDUCTOR CHIP 1.8UH 3225 SMD
496837-000 CABLE TERMINATION RG/U 178,404
VI-J72-EX CONVERTER MOD DC/DC 15V 75W
6374615-8 C/A LC-SC DUP 62.5/125, 8M
VE-B12-EY-S CONVERTER MOD DC/DC 15V 50W
相關代理商/技術參數
參數描述
SI2401 制造商:SILABS 制造商全稱:SILABS 功能描述:V.22BIS ISOMODEM㈢ WITH LOW-COST DAA
SI2401-C-FS 制造商:Silicon Laboratories Inc 功能描述:
SI2401DC-EVB 功能描述:子卡和OEM板 SI2401 Daughter Card RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
SI2401-FS 功能描述:電信線路管理 IC 2400b/s System Side 3rd Gen DAA Tech RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
Si2401FS08-EVB 功能描述:網絡開發工具 Si2401+Si3008 ISO modem Eval Board RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*