- 您現在的位置：買賣IC網 > PDF目錄16517 > SI2401FS08-EVB (Silicon Laboratories Inc)BOARD EVAL SI2401 + SI3008 PDF資料下載
參數資料
| 型號： | SI2401FS08-EVB |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 19/76頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL SI2401 + SI3008 |
| 標準包裝： | 1 |
| 系列： | ISOmodem® |
| 主要目的： | 電信，數據采集裝置（DAA） |
| 已用 IC / 零件： | SI2401 |
| 已供物品： | 板，CD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁
Si2401
26
Rev. 1.0
I
Chip Identification
This command causes the modem to echo the chip
revision for the Si2401 device.
A = Revision A
B = Revision B
C = Revision C, etc.
I6
Display the ISOmodem model number.
“2401” = Si2401.
:I
Interrupt Read
This command causes the ISOmodem chipset to report
the contents of the interrupt status register (S09). The
WOR, PPD, NLD, RI, OCD, and REV bits are also
cleared, and the INT is deactivated on this read.
M
Speaker On/Off Options
These options are used to control AOUT for use with a
call progress monitor speaker.
M0
Speaker always off.
M1
Speaker on until carrier established. The modem sets
SF4[3:2] (ARL) = 11b and SF4[1:0] (ATL) = 11b after a
connection is established.
M2
Speaker always on.
M3
Speaker on after last digit dialed, off at carrier detect.
O
Return to Online Mode
This command returns the modem to the online mode. It
is frequently used after an escape sequence to resume
communication with the remote modem.
RO
Turn-Around
This command initiates a V.23 “direct turnaround”
sequence and returns online.
S
S Register Control
SR=N
Write an S register. This command writes the value “N”
to the S-register specified by “R”. “R” is a hexidecimal
number, and “N” must also be a hexadecimal number
from 00–FF. This command does not wait for a carriage
return <CR> before taking effect.
Note:
Two digits must always be entered for both “R” and “N”.
SR?
Read an S register. This command causes the Si2401
to echo the value of the S-register specified by R in hex
format. R must be a hexidecimal number.
Note:
Two digits must always be entered for R.
w##
Write S Register in Binary
This command writes a register in binary format. The
first byte following the “w” is the address in binary
format, and the second byte is the data in binary format.
This is a more rapid method to write registers than the
“SR=N” command and is recommended for use by a
host microcontroller.
r#
Read S Register in Binary
This command reads a register in binary format. The
byte following the “r” is the address in binary format.
The modem echoes the contents of this register in
binary format. This is a more rapid method to read
registers
than
the
“SR?”
command
and
is
recommended for use by a host microcontroller. Modem
result codes should be disabled to avoid confusing a
result code with the value being read. (S62 = 40).
Notes:
1. w## and r# are not required to be on separate lines (i.e.,
no <CR> between them). Also, the result of an r# is
returned immediately without waiting for a <CR> at the end
of the AT command line.
2. Once a <CR> is encountered, “AT” is again required to
begin the next “AT” command.
m#
Monitor S Register in Binary
This command monitors a register in binary format. The
byte following the “m” is the address in binary format.
The Si2401 constantly transmits the contents of the
register at the set baud rate until a new byte is
transmitted to the device. The new byte is ignored and
viewed as a stop command. The modem result codes
should be disabled (as described above in r#) before
using this command.
q#
Read S Register in Binary
This command is exactly the same as the r# command;
however, the response from the Si2401 is formatted as
0x55 followed by the contents of the register in binary.
This guarantees that the register contents are always
preceded by 0x55 and allows the result codes to remain
enabled.
V
Result Code Options
V0
Result codes reported according to Table 14.
V1
Result codes reported with an additional carriage return
and line feed (default).
相關PDF資料 |
PDF描述 |
|---|---|
| 1-6374518-0 | C/A LC TO LC 900UM BUF 10 SM |
| EYM15DTKN-S288 | CONN EDGECARD 30POS .156 EXTEND |
| REC5-4815DRWZ/H6/C | CONV DC/DC 5W 18-72VIN +/-15VOUT |
| A3DDB-2418M | IDC CABLE- AKR24B/AE24M/AKR24B |
| VI-JVX-EZ-S | CONVERTER MOD DC/DC 5.2V 25W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI2401FS10-EVB | 功能描述:網絡開發工具 SI2401+SI3010 ISO MODEM EVAL. BOARD RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V |
| SI2401-FSR | 功能描述:電信線路管理 IC 2400b/s System Side 3rd Gen DAA Tech RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI2401URT-EVB | 功能描述:網絡開發工具 U 634-SI2401FS10-EVB RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V |
| SI2403 | 制造商:SILABS 制造商全稱:SILABS 功能描述:V.22BIS ISOMODEM CHIPSET WITH ERROR CORRECTION |
| SI2403-FT | 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET ISOMODEM 2.4KBPS 24TSSOP - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。