參數資料
型號： SI2401FS10-EVB
廠商： Silicon Laboratories Inc
文件頁數： 20/76頁
文件大小： 0K
描述： BOARD EVAL SI2401 UART INTERFACE
標準包裝： 1
系列： ISOmodem®
主要目的： 電信，調制解調器
嵌入式： 否
已用 IC / 零件： SI2401
主要屬性： 雙路 RJ-11 連接至電話線路，音頻連接器
次要屬性： RS-232，TTL 串行和 USB 接口
已供物品： 板，調制解調器，電源
相關產品： 336-1095-ND - IC ISOMODEM SYSTEM-SIDE 16SOIC
其它名稱： 336-1167
Si2401
Rev. 1.0
27
Z
Software Reset
The “Z” command initiates a software reset causing all
registers, with the exception of E0, which controls the
DTE settings, to default to their powerup value.
The hardware reset pin, RESET (Si2401, pin 8), is used
to reset the Si2401 to factory default settings.
z
Wakeup on Ring (lower-case z)
The Si2401 enters a low-power mode in which the DSP
and microcontroller are powered down. In this mode,
only the line-side device (Si3010) and the isolation
capacitor
communication
link
are
functional.
An
incoming ring signal or line transient causes the Si2401
to power up and echo an “R”. Any character received on
the RXD pin also causes the Si2401 to exit the wakeup-
on-ring state. Return from wake-on-ring can also be set
to trigger the INT pin by setting S08[6] (WORM) = 1b.
5.4. Alarm Industry AT Commands
The Si2401 supports a complete set of commands
necessary for making connections in security industry
systems. The Si2401 is configurable in two modes for
these
applications.
The
first
mode
uses
DTMF
messaging and is selected with the “!1” command. The
second
mode
uses
FSK
transmit
with
a
tone
acknowledgement and is selected with “!2”.
The following are a few general comments about the
use of “!” commands. Specific details for each command
are given below. The first instance of the “!” must be on
the same line as the ATDT or ATDP command. DRT
must be set to data mode (SE4[5:4] (DRT) = 0b) before
attempting to send tones after a “!” command. The three
data-mode escape sequences (“+++”, “escape” pin, and
“ninth-bit”) function in “!2” mode. However, using the
“+++” or “ninth-bit” is not recommended because
characters could be sent to and misinterpreted by the
remote modem. Only the “escape pin” (Si2401, pin 14)
is recommended for use in the “!2” mode. The “!1” mode
has a special escape provision described below. The AT
commands
for
Alarm
Industry
applications
are
described in Table 13.
5.4.1. !1
Dial number and follow the DTMF security protocol.
The format for this command is as follows:
ATDT<phone number>!1<message 1><CR>
K
!<message 2><CR>
K
!<message 3><CR>
K
!<message n><CR>
The modem dials the phone number and echoes “r”
(ring), “b” (busy), and “c” (connect) as appropriate. “c”
echoes only after the Si2401 detects the Handshake
Tone. After a 250 ms delay, the modem sends the
DTMF tones containing the first message data and
listens for a Kissoff Tone. If a Kissoff Tone shorter than
or
equal
to
the
value
stored
in
S36(KTL)
(default = 480 ms) is detected, the Si2401 echoes a “K”.
A “k” is echoed if the length of the Kissoff Tone is longer
than the S36(KTL) value. The controller can then send
the next message. All messages must be preceded by a
“!” and followed by a <CR> and received by the Si2401
within
250 ms
after
the
“K”
is
echoed.
Setting
S0C[0] (MCH) = 1b causes a “.” to be echoed when the
DTMF tone is turned on and a “/” character to be
echoed when the DTMF tone is turned off. This helps
the host monitor the status of the message being sent.
The previous message can be resent if the host
responds with a “~” after the Si2401 echoes a “K”. Any
character other than a “!” or a “~” sent to the modem
immediately after the “K” causes the modem to escape
to the command mode and remain off-hook. Any
character except “!” and “~” sent during the transmission
of a message causes the message to be aborted and
the modem to return to the command mode.
If the Kissoff Tone is not received within 1.25 seconds,
the modem echoes a “^”. A “~” from the host causes the
last message to be resent. Any character other than a
“!” or a “~” sent to the modem immediately after the “^”
causes the modem to escape to the command mode
and remain off-hook.
5.4.2. !2
Dial the number and follow the “SIA Format” protocol for
Alarm System Communications.
The modem dials the phone number and echoes “r”
(ring), “b” (busy), and “c” (connect) as appropriate. “c”
echoes only after the Si2401 detects the Handshake
Tone and the speed synchronization signal is sent. The
signaling is at 300 bps, half-duplex FSK. The host can
Table 13. AT Command Set Extensions
for the Alarm Industry
Command
Function
!1
Dial and switch to DTMF security
mode
!2
Dial and switch to “SIA Format”
X1
SIA half-duplex mode search
X2
SIA half-duplex return online as
transmitter
X3
SIA half-duplex return online as
receiver
相關PDF資料
PDF描述
UPA0J272MPD1TD CAP ALUM 2700UF 6.3V 20% RADIAL
UPA0J222MPD1TD CAP ALUM 2200UF 6.3V 20% RADIAL
GBC19DRAS CONN EDGECARD 38POS R/A .100 SLD
CM322522-2R2JL INDUCTOR CHIP 2.2UH 3225 SMD
RR70G821MDN1 CAP ALUM 820UF 4V 20% RADIAL
相關代理商/技術參數
參數描述
SI2401-FSR 功能描述:電信線路管理 IC 2400b/s System Side 3rd Gen DAA Tech RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
SI2401URT-EVB 功能描述:網絡開發工具 U 634-SI2401FS10-EVB RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
SI2403 制造商:SILABS 制造商全稱:SILABS 功能描述:V.22BIS ISOMODEM CHIPSET WITH ERROR CORRECTION
SI2403-FT 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET ISOMODEM 2.4KBPS 24TSSOP - Rail/Tube
SI2404 制造商:未知廠家 制造商全稱:未知廠家 功能描述:V.90, V.34, V.32BIS, V.22BIS ISOMODEM?? WITH GLOBAL DAA
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*