參數資料
型號： SI2415-D-GT
廠商： Silicon Laboratories Inc
文件頁數： 17/60頁
文件大?。?/td> 0K
描述： IC ISOMODEM GLOBAL DAA 24TSSOP
標準包裝： 62
系列： *
Si2457/34/15/04
24
Rev. 1.3
Sn=x
Set S-register n to value x (where n and x are decimal values).
Vn
Result code type (see Table 12 on page 38).
V0
Numeric result codes.
V1
Verbal result codes
Xn
Call Progress Monitor (CPM)—This command controls which CPM signals are monitored
and reported to the host from the Si2457/34/15/04. (See Table 12 on page 38.)
X0
Basic results; disable CPM—Blind dial (does not wait for dial tone). CONNECT message
does not include speed.
X1
Extended results; disable CPM—Blind dial. CONNECT message includes speed.
X2
Extended results and detect dial tone only—Add dial tone detection to X1 mode. Does not
blind dial.
X3
Extended results and detect busy only—Add busy tone detection to X1 mode.
X4
Extended results, full CPM—Full CPM enabled, CONNECT message includes speed.
X5
Extended results—Full CPM enabled including ringback detection. Adds ringback detection
to X4 mode.
Yn
Long space disconnect—Modem hangs up after 1.5 seconds or more of continuous space
while on-line.
Y0
Disable.
Y1
Enable.
Z
Hard Reset—This command is functionally equivalent to pulsing the RESET pin low. (See
:E
Read from serial EEPROM.
:I
Interrupt Read—This command causes the ISOmodem to report the lower 8 bits of the
interrupt register I/O Control 0 (U70). The CID, OCD, PPD, and RI bits also are cleared, and
the INT pin (INT bit in parallel mode) is deactivated on this read.
:M
Write to serial EEPROM.
:P
Program RAM Write—This command is used to upload firmware supplied by Silicon Labs to
the Si2457/34/15/04. The format for this command is AT:Paaaa,xxxx,yyyy,.... where aaaa is
the first address in hexadecimal and xxxx,yyyy,.... is data in hexadecimal. Only one :P com-
mand is allowed per AT command line. No other commands can be concatenated in the :P
command line. This command is only for use with special files provided by Silicon Laborato-
ries. Do not attempt to use this command for any other purpose.
:R
User-Access Register Read—This command allows the user to read from the user-access
registers (see "6. User-Access Registers (U-Registers)" on page 44). The format is “AT:Raa”,
where:
aa = user-access address in hexadecimal.
The “AT:R” command causes all the U- registers to be displayed.
Table 8. Basic AT Command Set (Command Defaults in Bold) (Continued)
Command
Action
相關PDF資料
PDF描述
VE-J6Y-IX-B1 CONVERTER MOD DC/DC 3.3V 49.5W
VI-2N2-IX-F2 CONVERTER MOD DC/DC 15V 75W
VI-2N2-IX-F1 CONVERTER MOD DC/DC 15V 75W
VI-2N1-IX-F4 CONVERTER MOD DC/DC 12V 75W
VE-J6Y-IW-B1 CONVERTER MOD DC/DC 3.3V 66W
相關代理商/技術參數
參數描述
SI2415-D-GTR 制造商:Silicon Laboratories Inc 功能描述:14.4 KBPS ISOMODEM SYSTEM-SIDE 制造商:Silicon Laboratories Inc 功能描述:14.4 KBPS ISOMODEM SYSTEM-SIDE - LEAD-FREE - Tape and Reel 制造商:Silicon Laboratories Inc 功能描述:IC ISOMODEM GLOBAL DAA 24TSSOP 制造商:Silicon Laboratories Inc 功能描述:14.4 kbps ISOmodem System-Side PBF
Si2415FS08-EVB 功能描述:網絡開發工具 16-pin Si2415+Si3008 ISOmodem Eval Board RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
Si2415FS18-EVB 功能描述:網絡開發工具 16-pin Si2415+Si3018 ISOmodem Eval Board RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
SI2415-FT 功能描述:電信線路管理 IC RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray
Si2415FT08-EVB 功能描述:網絡開發工具 24-pin Si2415+Si3008 ISOmodem Eval Board RoHS:否 制造商:Rabbit Semiconductor 產品:Development Kits 類型:Ethernet to Wi-Fi Bridges 工具用于評估:RCM6600W 數據速率:20 Mbps, 40 Mbps 接口類型:802.11 b/g, Ethernet 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*