- 您現在的位置：買賣IC網 > PDF目錄10901 > SI3015-BS (Silicon Laboratories Inc)IC ISOMODEM LINE-SIDE DAA 16SOIC PDF資料下載
參數資料
| 型號： | SI3015-BS |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 21/64頁 |
| 文件大小： | 0K |
| 描述： | IC ISOMODEM LINE-SIDE DAA 16SOIC |
| 標準包裝： | 48 |
| 系列： | ISOmodem® |
| 數據格式： | V.90 |
| 波特率： | 2.4k |
| 電源電壓： | 3.3V，5V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SOIC N |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
Si3038
28
Rev. 2.01
On-Hook Line Monitor
The Si3038 allows the user to receive line activity when in
an on-hook state. The LINE1_CID/LINE2_CID bit in
slot 12 enables a low-power ADC which digitizes the
signal passed across the RNG1/2 pins. This signal is
passed across the ISOcap to the AC’97 controller. A
current of approximately 450
A is drawn from the line
when this bit is activated. This mode is typically used to
detect caller ID data (see the “Caller ID” section).
The on-hook line monitor can also be used to detect
whether a phone line is physically connected to the Si3014
and associated circuitry. If a line is present and the
LINE1_CID/LINE2_CID bit is set, SDATA_IN will have a
near zero value and the LCS[3:0] bits will read 1111b. Due
to the nature of the low-power ADC, the data presented on
SDATA_IN could have up to a 10% dc Offset.
If no line is connected, the output of SDATA_IN will move
towards a negative full scale value (–32768). The value is
guaranteed to be at least 89% of negative full scale. In
addition, the LCS[3:0] bits will be zero.
Caller ID
The Si3038 provides the designer with the ability to
pass caller ID data from the phone line to the AC-link
interface.
In countries where the caller ID data is passed on the
phone line between the first and second rings, the
following method should be utilized to capture the caller
ID data. The RDTP and RDTN register bits should be
monitored to determine the completion of the first ring.
After completion of the first ring, the AC’97 controller
should set the SQLH bit (register 5Ch) for a period of at
least 1 ms. This resets the ac coupling network on the
ring input in preparation for the caller ID data. The
SQLH bit is then cleared, and the LINE1_CID/
LINE2_CID (slot 12, GPIO2/12) should be asserted to
enable the caller ID data to be passed to the AC’97
controller on SDATA_IN. This bit enables a low-power
ADC (approximately 450
A is drawn from the line)
which digitizes the signal passed across the RNG1/2
pins. This signal is passed across the ISOcap to the
AC’97 controller. The LINE1_CID/LINE2_CID bit should
be cleared after the caller ID data is received and prior
to the second ring.
In systems where the caller ID data is preceded by a
line polarity (battery) reversal, the following method
should be used to capture the caller ID data. The
Si3038 supports both full- and half-wave rectified ring
detection. Because a polarity reversal will trip either the
RDTP or RDTN ring detection bits, the user must
distinguish between a polarity reversal and a ring. This
is accomplished using the full-wave ring detector in the
device. The lowest specified ring frequency is 15 Hz;
therefore, if a battery reversal occurs, the AC’97
controller should wait a minimum of 40 ms to verify that
the event observed is a battery reversal and not a ring
signal. This time is greater than half the period of the
longest ring signal. If another edge is detected during
this 40 ms pause, this event is characterized as a ring
signal and not a battery reversal. If it is a battery
reversal, the AC’97 controller should set the SQLH bit
for a period of at least 1 ms. This resets the ac coupling
network on the ring input in preparation for the caller ID
data. The SQLH bit is then cleared, and the LINE1_CID/
LINE2_CID should be asserted to enable the caller ID
data to be passed to the AC’97 controller and presented
on SDATA_IN. The bit should be cleared after the AC’97
controller has received the caller ID data.
Due to the nature of the low-power ADC, the data
presented on SDATA_IN will have up to a 10% dc
Offset. The caller ID decoder must either use a high
pass or band pass filter to accurately retrieve the caller
ID data.
Loop Current Monitor
It may be desirable to have a measurement of the loop
current being drawn from the line. This measurements
can be used to tell whether a telephone line is
connected, whether a parallel handset has been picked
up, or if excessive loop current is present.
When the system is in an off-hook state, the LCS bits of
register 5Eh indicate the approximate amount of dc loop
current. The LCS is a 4-bit value ranging from zero to
fifteen. Each unit represents approximately 6 mA of loop
current from LCS codes 1–14. The typical LCS transfer
function is shown in Figure 26:
Figure 26. Typical LCS Transfer Function
An LCS value of zero means the loop current is less
than required for normal operation and the system
should be on-hook. Typically, an LCS value of 15 means
the loop current is greater than 155 mA.
The LCS detector has a built-in hysteresis of 2 mA. This
allows for a stable LCS value when the loop current is
0
5
10
15
LCS
BIT
0 6 12 18 24 30 36 42 48 54 60 66 72
155
78 84 90 96
Loop Current (mA)
相關PDF資料 |
PDF描述 |
|---|---|
| PIC16C54T-XTE/SO | IC MCU OTP 512X12 18SOIC |
| PIC16C54T-RC/SS | IC MCU OTP 512X12 20SSOP |
| VE-262-IX-F2 | CONVERTER MOD DC/DC 15V 75W |
| PIC16C54T-RC/SO | IC MCU OTP 512X12 18SOIC |
| PIC16C54T-RCI/SS | IC MCU OTP 512X12 20SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI3015-BSR | 功能描述:電信線路管理 IC CONTACT SILICON LABS FOR AVAILABILITY RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI3015-E-FSR | 制造商:Silicon Laboratories Inc 功能描述: |
| Si3015-F-FS | 功能描述:電信線路管理 IC Si2400 ISOmodem Line-Side RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI3015-F-FSR | 制造商:Silicon Laboratories Inc 功能描述:Modem Chip Chipset 2.4Kbps 16-Pin SOIC T/R 制造商:Silicon Laboratories Inc 功能描述:MODEM CHIP CHIPSET ISOMODEM 2.4KBPS 16SOIC - Tape and Reel 制造商:Silicon Laboratories 功能描述:Modem Chip Chipset 2.4Kbps 16-Pin SOIC T/R |
| SI3015-FS | 功能描述:IC ISOMODEM LINE-SIDE DAA 16SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 調制解調器 - IC 和模塊 系列:ISOmodem® 標準包裝:25 系列:- 數據格式:V.21，V.22，V.23，V.29，V.32，V.34，V.90，V.92，Bell 103，Bell 212A 波特率:33.6k 電源電壓:3.3V 安裝類型:- 封裝/外殼:- 供應商設備封裝:- 包裝:托盤 配用:591-1013-ND - KIT DEV SOCKETMODEM PARALLEL591-1009-ND - KIT DEV SRL SOCKETMODEM UNIVERSL 其它名稱:MT5656SMI-P-V-34.R2-SPMT5656SMI-P-V-34.R2-SP-NDQ4711574 |
發布緊急采購，3分鐘左右您將得到回復。