- 您現在的位置：買賣IC網 > PDF目錄10999 > SI3202-G-GS (Silicon Laboratories Inc)IC LINEFEED INTRFC 125V 16SOIC PDF資料下載
參數資料
| 型號： | SI3202-G-GS |
| 廠商： | Silicon Laboratories Inc |
| 文件頁數： | 96/112頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LINEFEED INTRFC 125V 16SOIC |
| 標準包裝： | 48 |
| 功能： | 用戶線路接口概念（SLIC），CODEC |
| 接口： | GCI，PCM，SPI |
| 電路數： | 2 |
| 電源電壓： | 3.13 V ~ 5.25 V |
| 電流 - 電源： | 65mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm Width）裸露焊盤 |
| 供應商設備封裝： | 16-SOIC N |
| 包裝： | 管件 |
| 包括： | 電池切換，BORSCHT 功能，DTMF 生成和解碼，F(xiàn)SK 音調生成，調制解調器和傳真音調檢測 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁當前第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁
Si3220/25 Si3200/02
84
Rev. 1.3
Not
Recommended
fo
r N
ew
D
esi
gn
s
3.31. General Circuit Interface
The Dual ProSLIC devices also contain an alternate
communication interface to the SPI and PCM control
and data interface. The general circuit interface (GCI) is
used for the transmission and reception of both control
and data information onto a GCI bus. The PCM and GCI
interfaces are both four-wire interfaces and share the
same pins. The SPI control interface is not used as a
communication interface in the GCI mode but rather as
hard-wired
channel
selector
pins.
The
selection
between PCM and GCI modes is performed out of reset
to select the communication mode and how the pins are
used in each mode.
If GCI mode is selected, the following pins must be tied
to the correct state to select one of eight subframe
timeslots in the GCI frame (described below). These
pins must remain in this state while the Dual ProSLIC is
operating. Selecting a particular subframe causes that
individual Dual ProSLIC device to transmit and receive
on the appropriate subframe in the GCI frame, which is
initiated by an FSYNC pulse. No further register settings
are needed to select which subframe a device uses,
and the subframe for a particular device cannot be
changed while in operation.
In GCI mode, the PCLK input requires either a
2.048 MHz or a 4.096 MHz clock signal, and the
FSYNC input requires an 8 kHz frame sync signal. The
overall unit of data used to communicate on the GCI
highway is a frame 125 s in length. Each frame is
initiated by a pulse on the FSYNC pin whose rising
edge signifies the beginning of the next frame. In 2x
PCLK mode, the user sees twice as many PCLK cycles
during each 125 s frame versus 1x PCLK mode. Each
frame consists of eight fixed timeslot subframes that are
assigned by the subframe select pins as described
above (SDI, SDO, and CS). Within each subframe are
four channels (bytes) of data including two voice data
channels, B1 and B2, one Monitor channel, M, used for
initialization and setup of the device, and one Signaling
and Control channel, SC, used for communicating the
status of the device and initiating commands. Within the
SC channel are six Command/Indicate (C/I) bits and two
Table 45. PCM or GCI Mode Selection
SDITHRU SCLK
Mode Selected
0
GCI Mode—1x PCLK (2.048 MHz)
0
1
GCI Mode—2x PCLK (4.096 MHz)
1
x
PCM Mode
Note:
Values shown are the states of the pins at the rising
edge of RESET.
Table 46. Pin Functionality in PCM or GCI Mode
Pin Name
PCM Mode
GCI Mode
CS
SPI Chip Select
Channel Selector,
bit 0
SCLK
SPI Clock Input
PCLK Rate
Selector
SDI
SPI Serial Data Input
Channel Selector,
bit 2
SDO
SPI Serial Data
Output
Channel Selector,
bit 1
SDITHRU
SPI Data Throughput
pin for Daisy Chaining
Operation (Connects
to the SDI pin of the
subsequent device in
the daisy chain)
PCM/GCI Mode
Selector
FSYNC
PCM Frame Sync
Input
GCI Frame Sync
Input
PCLK
PCM Input Clock
GCI Input Clock
DTX
PCM Data Transmit
GCI Data Transmit
DRX
PCM Data Receive
GCI Data Receive
Note:
This table denotes pin functionality after the rising
edge of RESET and mode selection.
Table 47. GCI Mode Subframe Selection
SDI
SDO
CS
GCI Subframe 0 Selected
(Voice channels 1–2)
11
1
GCI Subframe 1 Selected
(Voice channels 3–4)
11
0
GCI Subframe 2 Selected
(Voice channels 5–6)
10
1
GCI Subframe 3 Selected
(Voice channels 7–8)
10
0
GCI Subframe 4 Selected
(Voice channels 9–10)
01
1
GCI Subframe 5 Selected
(Voice channels 11–12)
01
0
GCI Subframe 6 Selected
(Voice channels 13–14)
00
1
GCI Subframe 7 Selected
(Voice channels 15–16)
00
0
相關PDF資料 |
PDF描述 |
|---|---|
| S9S08AW32E5VFGE | MCU 32K FLASH AUTO 44-LQFP |
| MC9S08AW32VFGE | MCU 8BIT 32K FLASH 44-LQFP |
| MC908JL16CDWER | IC MCU 16K FLASH 28-SOIC |
| S9S08SG8E2MTG | MCU 8K FLASH 16-TSSOP |
| SI3200-G-GS | IC SLIC/CODEC 125V LINE 16SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SI3202-G-GSR | 功能描述:電信線路管理 IC 125 V Linefeed Interface IC RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| SI3203 | 制造商:SILABS 制造商全稱:SILABS 功能描述:Quad ProSLIC㈢ Programmable CMOS SLIC/Codec |
| SI3203-A-FM | 制造商:Silicon Laboratories Inc 功能描述: |
| SI3203-A-FMR | 制造商:Silicon Laboratories Inc 功能描述: |
| SI3203-A-GM | 制造商:Silicon Laboratories Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。