參數資料
型號: SP508CEB
英文描述: Evaluation Board Manual
中文描述: 評估板手冊
文件頁數: 3/10頁
文件大小: 72K
代理商: SP508CEB
rev. 7/7/03
SP508 Evaluation Board Manual
3
Copyright 2003 Sipex Corporation
SP508 EVALUATION BOARD
Figure 2: RS-232 & EIA530 Connector (ISO 2110),
DTE Connector
σ
DB-25 Male, DCE Connector
σ
DB-
25 Female
1
13
14
25
BOARD LAYOUT
1. The SP508 Evaluation board takes ad-
vantage of the products PCB friendly flow
through pinout in its design as shown in
Figure 1.
2. The SP508 Evaluation Board has been
designed to easily and conveniently provide
access to all inputs and outputs under test.
3. Figure 1 is a block diagram of the evalu-
ation board showing the layout of the SP508
Evaluation Board. The block diagram shows
the location of the driver and receiver ac-
cess points as well as the DIP switches, V
CC
,
GND and the DB-25 Connector.
4. I/O Pinouts
The SP508 Evaluation Board has been de-
signed to easily and conveniently provide
access to all inputs and outputs to the device
under test. Position the Board with the DB-
25 connector at the top and the Dip switches
at the bottom. From this orientation , all
driver inputs and outputs are on the right-
hand side and all receiver inputs and out-
puts are on the left-hand side eof the Board.
4.1. Each Driver has probe points for the
input and outputs. There is a ground buss to
the right of the drive outputs for the addition
of loads to the driver outputs and to jumper
the V.35 that is associated with the SD, TT,
and ST driver. Each V.35 driver has a
separate ground for the V.35 termination
network internal to the device.
4.2. Each Receiver has probe points for the
inputs and outputs. there is a ground buss
to the left of the receiver outputs and a
separate pin for the V.10 termination ground.
5. At the bottom of the board is a series of
six(6) DIP switches. The DIP switch on the
far left is for D_LATCH and TERM_OFF.
Each driver and receiver has its own indi-
vidual enable pin. The DIP switches to
control the enable pins are located as the
top center bank of switches for the driver and
the middle center bank of switches for the
receiver. The bottom center set of DIP
switches is for the 3 bit decoder and the
loopback control pin. The right hand DIP
switches allow the user to tie the ST driver
outputs to the TxC receiver inputs and the
RRC driver outputs to the RRT receiver
inputs.
6. Also located on the SP508 evaluation
board are the four 10uf charge pump capaci-
tors, a 10uf bypass capacitor for V
CC
and a
50
termination resistor.
7. Table 1 shows the pinout of the DB-25
connector used to connect to a communica-
tion analyzer such as the TTC Firebird 6000.
相關PDF資料
PDF描述
SP508 Rugged 40Mbps, 8 Channel Multiprotocol Transceiver with Programmable DCE/DTE and Termination Resistors(40Mbps差分傳輸速率,8通道多協議收發器(帶可編程DCE/DTE和終端電阻器))
SP514 WAN Multi-Mode Serial Transceiver
SP514CF WAN Multi-Mode Serial Transceiver
SP516 20Mbps 7 Driver, 7 Receiver Multiprotocol Serial Transceiver with Termination Disable
SP516CF 20Mbps 7 Driver, 7 Receiver Multiprotocol Serial Transceiver with Termination Disable
相關代理商/技術參數
參數描述
SP508CF 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Rugged 20Mbps, 8 Channel Multi-Protocol Transceiver with Programmable DCE/DTE and Termination Resistors
SP508CF-L 功能描述:外圍驅動器與原件 - PCI 20MBPS 8CH MULTI 0-70C RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
SP508EB 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Evaluation Board Manual
SP508ECF-L 制造商:Exar Corporation 功能描述:Octal Transmitter/Receiver RS-232/RS-449/RS-530 100-Pin LQFP 制造商:Exar Corporation 功能描述:SP508ECF-L 制造商:Exar Corporation 功能描述:IC, MULTIPROTOCOL TXRX, 20MBPS, LQFP-100; Device Type:Transceiver; IC Interface Type:RS232, RS449, EIA530, EIA530A; No. of Drivers:8; Supply Voltage Min:4.75V; Supply Voltage Max:5.25V; Driver Case Style:LQFP; No. of Pins:100 ;RoHS Compliant: Yes
SP508EEF-L 制造商:Exar Corporation 功能描述:Octal Transmitter/Receiver RS-232/RS-449/RS-530 100-Pin LQFP 制造商:Exar Corporation 功能描述:SP508EEF-L 制造商:Exar Corporation 功能描述:IC, MULTIPROTOCOL TXRX, 20MBPS, LQFP-100; Device Type:Transceiver; IC Interface Type:RS232, RS449, EIA530, EIA530A; No. of Drivers:8; Supply Voltage Min:4.75V; Supply Voltage Max:5.25V; Driver Case Style:LQFP; No. of Pins:100 ;RoHS Compliant: Yes