- 您現在的位置：買賣IC網 > PDF目錄372186 > SP508CEB Evaluation Board Manual PDF資料下載
參數資料
| 型號： | SP508CEB |
| 英文描述： | Evaluation Board Manual |
| 中文描述： | 評估板手冊 |
| 文件頁數： | 7/10頁 |
| 文件大?。?/td> | 72K |
| 代理商： | SP508CEB |
rev. 7/7/03
SP508 Evaluation Board Manual
7
Copyright 2003 Sipex Corporation
Driver Receiver Remote Loopback.
The following example uses the ST driver
looped back into the TxC receiver, using the
3 bit decoder configure the SP508 for the
desired protocol. Connect a jumper cable
between the ST(a) pin and the TxC(a) pin. If
your mode select is for a differential driver/
receiver, then also connect a jumper cable
between the ST(b) pin and the TxC(b) pin.
next connect a signal generator to the ST
input pin. The signal generator output must
be a TTL-level output at a frequency within
the acceptable range of the driver mode
under test. Be sure that the STEN and the
TxCEN DIP switches are set to enable the
ST driver and TxC receiver and that the DIP
switches tying the ST driver to the TxC
receiver are off (refer to section 5.0 Dip
switch guide). The driver outputs are now
connected back to the receiver inputs so
that the driver input to receiver output can
be examined. This configuration is similar
for the other drivers.
Driver Receiver Local Loopback
The SP508 has the ability to provide an
internal loopback. This feature is invoked by
a logic “0” on the LOOPBACK pin. The
driver input and receiver output characteris-
tics adhere to the appropriate specifications
outlined in the data sheet under loopback
conditions. The LOOPBACK pin has in in-
ternal pull-up resistor so that the SP508
defaults to normal operation during power-
up or if the pin is left floating.
DCE DTE selectable configuration
Configure the decoder for the desired
mode.
The SP508 evaluation board has dip
switches setup to allow for the evaluation
of a selectable DCE DTE configuration.
Switch the STEN and RRCEN to the ON
position. This will disable the ST and RRC
driver outputs. (Refer to the DIP switch
guide on Page 8)
Switch the <TxCEN> and <RRTEN>
switches to the ON position. This will dis-
able the TxC and RRT receiver inputs.
(Refer to the DIP switch guide on Page 8)
Switch the ST(A), ST(B), TxC(A), and
TxC(B) switches to the ON position. This
ties the ST driver outputs to the TxC Re-
ceiver inputs.
Switch the RRC(A), RRC(B), RRT(A), and
RRT(B) switches to the ON position. This
ties the RRC driver outputs to the RRC
receiver inputs.
To enable a DTE configuration switch the
STEN and RRCEN switch to the OFF
position. Be sure the TxC and RRT receiv-
ers are disabled by switching the TxCEN
and RRTEN switches to the ON position.
(Refer to the DIP switch guide on Page 8)
To enable a DCE configuration switch the
TxCEN and RRTEN to the OFF position.
Be sure to disable the ST and RRC driver
outputs by switching the STEN and RRCEN
switches to the ON position. (Refer to the
DIP switch guide on Page 8)
System Level Evaluation
The DB-25 Connect if configured as a DTE
for EIA-530 pinout. In order to connect
other DCE equipment or network analyz-
ers ( i.e. the TTC Firebird 6000A), the RxC
receiver output must looped back into the
TxCE driver input. The RxD output can
also be looped back to the TxD input.
If connecting the evaluation board to a
microcontroller such as the Motorola
MC68360, jumper wires of the driver in-
puts and receiver outputs must connect to
the
μ
C’s appropriate pins.
USING THE EVALUATION BOARD: continued
相關PDF資料 |
PDF描述 |
|---|---|
| SP508 | Rugged 40Mbps, 8 Channel Multiprotocol Transceiver with Programmable DCE/DTE and Termination Resistors(40Mbps差分傳輸速率，8通道多協議收發器（帶可編程DCE/DTE和終端電阻器）) |
| SP514 | WAN Multi-Mode Serial Transceiver |
| SP514CF | WAN Multi-Mode Serial Transceiver |
| SP516 | 20Mbps 7 Driver, 7 Receiver Multiprotocol Serial Transceiver with Termination Disable |
| SP516CF | 20Mbps 7 Driver, 7 Receiver Multiprotocol Serial Transceiver with Termination Disable |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP508CF | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Rugged 20Mbps, 8 Channel Multi-Protocol Transceiver with Programmable DCE/DTE and Termination Resistors |
| SP508CF-L | 功能描述:外圍驅動器與原件 - PCI 20MBPS 8CH MULTI 0-70C RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| SP508EB | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Evaluation Board Manual |
| SP508ECF-L | 制造商:Exar Corporation 功能描述:Octal Transmitter/Receiver RS-232/RS-449/RS-530 100-Pin LQFP 制造商:Exar Corporation 功能描述:SP508ECF-L 制造商:Exar Corporation 功能描述:IC, MULTIPROTOCOL TXRX, 20MBPS, LQFP-100; Device Type:Transceiver; IC Interface Type:RS232, RS449, EIA530, EIA530A; No. of Drivers:8; Supply Voltage Min:4.75V; Supply Voltage Max:5.25V; Driver Case Style:LQFP; No. of Pins:100 ;RoHS Compliant: Yes |
| SP508EEF-L | 制造商:Exar Corporation 功能描述:Octal Transmitter/Receiver RS-232/RS-449/RS-530 100-Pin LQFP 制造商:Exar Corporation 功能描述:SP508EEF-L 制造商:Exar Corporation 功能描述:IC, MULTIPROTOCOL TXRX, 20MBPS, LQFP-100; Device Type:Transceiver; IC Interface Type:RS232, RS449, EIA530, EIA530A; No. of Drivers:8; Supply Voltage Min:4.75V; Supply Voltage Max:5.25V; Driver Case Style:LQFP; No. of Pins:100 ;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。