- 您現在的位置：買賣IC網 > PDF目錄372194 > SP791EK Evaluation Board Manual PDF資料下載
參數資料
| 型號： | SP791EK |
| 英文描述： | Evaluation Board Manual |
| 中文描述： | 評估板手冊 |
| 文件頁數： | 11/19頁 |
| 文件大?。?/td> | 202K |
| 代理商： | SP791EK |
11
SP791DS/08 SP791 Low Power Microprocessor Supervisory with Battery Switch-Over
Copyright 2000 Sipex Corporation
The 10ns maximum CE propagation from CE
IN
to CE
OUT
enables the
SP791
to be used with
most
μ
Ps.
CHIP-ENABLE INPUT
CE
IN
is high impedance (disabled mode) while
RESET is asserted.
During a power-down sequence where V
CC
falls
below 4.65V, CE IN assumes a high impedance
state when the voltage at CE
IN
goes high or
15
μ
s after RESET is asserted, whichever
occurs first, (
Figure 7
).
During a power-up sequence, CE
IN
remains
high impedance until RESET is deasserted.
In the high-impedance mode, the leakage
currents into this input are less than 1
μ
A over
temperature. In the low-impedance mode, the
impedance of CE
IN
appears as a 65
resistor
in series with the load at CE
OUT
.
The propagation delay through the CE
transmission gate depends on both the source
impedance of the drive to CE
IN
and the
capacitive loading on CE
OUT
(see the Chip-
Enable Propagation Delay vs. CE
OUT
Load
Capacitance graph in the
Typical Operating
Characteristics).
The CE propagation delay is
defined from the 50% point on CE
IN
to the 50%
point on CE
OUT
using a 50
driver with 50pF
load capacitance as in
Figure 8
. For minimum
propagation delay, minimize the capacitive load
at CE
OUT
and use a low output-impedance
driver.
CHIP-ENABLE OUTPUT
In the enabled mode, the impedance of CE
OUT
is equivalent to 65
in series with the source
driving CE
IN
. In the disabled mode, the 65
transmission gate is off and CE
OUT
is actively
pulled to V
OUT
. This source turns off when the
transmission gate is enabled.
Figure 8. CE Propagation Delay Test Circuit
Figure 7. Reset and Chip-Enable Timing
+5V
Vcc
50
Driver
GND
CE
IN
CE
OUT
50pF
C
LOAD
C orporation
Vcc
RESET
CE
IN
CE
OUT
RESET
15
μ
s
100
μ
s
100
μ
s
THRESHOLD
相關PDF資料 |
PDF描述 |
|---|---|
| SP791EN | Low Power Microprocessor Supervisory with Battery Switch-Over |
| SP791EP | Low Power Microprocessor Supervisory with Battery Switch-Over |
| SP800LCT | Low Power Microprocessor Supervisory with Battery Switch-Over |
| SP800LEN | Low Power Microprocessor Supervisory with Battery Switch-Over |
| SP800LEP | Low Power Microprocessor Supervisory with Battery Switch-Over |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SP791EN | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Low Power Microprocessor Supervisory with Battery Switch-Over |
| SP791EN-L | 功能描述:監控電路 LW PWR MICRO 5.5V 25mA-250mA BAT SW/OV RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| SP791EN-L/TR | 功能描述:監控電路 LW PWR MICRO 5.5V 25mA-250mA BAT SW/OV RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| SP791EP | 制造商:SIPEX 制造商全稱:Sipex Corporation 功能描述:Low Power Microprocessor Supervisory with Battery Switch-Over |
| SP7AL | 制造商:Hubbell Wiring Device-Kellems 功能描述:ALMOND PAINTED STEEL SGL. RECEPTACLE |
發布緊急采購，3分鐘左右您將得到回復。