"#$%#
SBFS025A JUNE 2004 REVISED JULY 2004
www.ti.com
2
ABSOLUTE MAXIMUM RATINGS
(1)
Core Supply Voltage
VDD18
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VDD33
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Digital I/O Supply Voltage, VIO
Digital Input Voltage
. . . . . . . . . . . . . . . . . . . . . . . . .
Operating Case Temperature Range, TC
Storage Temperature Range, TSTG
(1)Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods
may degrade device reliability. These are stress ratings only, and
functional operation of the device at these or any other conditions
beyond those specified is not supported.
0.3V to +2.0V
0.3V to +4.0V
0.3V to +4.0V
0.3V to +4.0V
40
°
C to +85
°
C
65
°
C to +150
°
C
. . . . . . . . . . . . . . . .
. . . . . . . .
. . . . . . . . . . .
This integrated circuit can be damaged by ESD. Texas
Instruments recommends that all integrated circuits be
handled with appropriate precautions. Failure to observe
proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to
complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could
cause the device not to meet its published specifications.
ORDERING INFORMATION
For the most current package and ordering information, see the Package Option Addendum located at the end of this data
sheet.
ELECTRICAL CHARACTERISTICS
All specifications at TA = +25
°
C, VDD33 = +3.3V, VIO = +3.3V, REGEN = High, and VDD18 floating, unless otherwise noted.
SRC4194
TYP
PARAMETER
CONDITIONS
MIN
MAX
UNITS
DYNAMIC PERFORMANCE
Resolution
Input Sampling Frequency, fsIN
Output Sampling Frequency, fsOUT
INPUT/OUTPUT SAMPLING RATIO
Upsampling
Downsampling
DYNAMIC RANGE(1)
24
Bits
kHz
kHz
4
4
212
212
1:16
16:1
BW = 20Hz to fsOUT/2, 60dBFS Input
fIN = 1kHz, A-Weighted
44.1kHz:48kHz
48kHz:44.1kHz
48kHz:96kHz
44.1kHz:192kHz
96kHz:48kHz
192kHz:12kHz
192kHz:32kHz
192kHz:48kHz
32kHz:48kHz
12kHz:192kHz
TOTAL HARMONIC DISTORTION + NOISE(1)
143
143
143
141
144
144
144
144
143
141
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
BW = 20Hz to fsOUT/2, 0dBFS Input
fIN = 1kHz, Unweighted
44.1kHz:48kHz
48kHz:44.1kHz
48kHz:96kHz
44.1kHz:192kHz
96kHz:48kHz
192kHz:12kHz
192kHz:32kHz
192kHz:48kHz
32kHz:48kHz
12kHz:192kHz
Interchannel Gain Mismatch
Interchannel Phase Deviation
(1)Dynamic performance is measured with an Audio Precision System Two Cascade or Cascade Plus test system.
(2)fsMIN = min (fsIN, fsOUT).
(3)fsMAX = max (fsIN, fsOUT).
(4)Power-supply current for the power-down modes is measured without loading.
(5)Dynamic power-supply current measurements are performed with 2mA active loads on the excercized outputs.
140
140
140
137
140
140
141
141
140
137
0
0
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
dB
degrees