- 您現在的位置：買賣IC網 > PDF目錄3755 > ST16C550IQ48TR-F (Exar Corporation)IC UART FIFO 16B SGL 48TQFP PDF資料下載
參數資料
| 型號： | ST16C550IQ48TR-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 10/35頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO 16B SGL 48TQFP |
| 標準包裝： | 1,500 |
| 特點： | * |
| 通道數： | 1，UART |
| FIFO's： | 16 字節 |
| 電源電壓： | 2.97 V ~ 5.5 V |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-TQFP |
| 供應商設備封裝： | 48-TQFP（7x7） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
ST16C550
18
Rev. 5.01
LCR BIT-6:
When enabled the Break control bit causes a break
condition to be transmitted (the TX output is forced to a
logic 0 state). This condition exists until disabled by
setting LCR bit-6 to a logic 0.
Logic 0 = No TX break condition. (normal default
condition)
Logic 1 = Forces the transmitter output (TX) to a logic
0 for alerting the remote receiver to a line break
condition.
LCR BIT-7:
The internal baud rate counter latch and Enhance
Feature mode enable.
Logic 0 = Divisor latch disabled. (normal default condi-
tion)
Logic 1 = Divisor latch and enhanced feature register
enabled.
Modem Control Register (MCR)
This register controls the interface with the modem or
a peripheral device.
MCR BIT-0:
Logic 0 = Force -DTR output to a logic 1. (normal
default condition)
Logic 1 = Force -DTR output to a logic 0.
MCR BIT-1:
Logic 0 = Force -RTS output to a logic 1. (normal
default condition)
Logic 1 = Force -RTS output to a logic 0.
MCR BIT-2:
Logic 0 = Set -OP1 output to a logic 1. (normal default
condition)
Logic 1 = Set -OP1 output to a logic 0.
MCR BIT-3:
Logic 0 = Set -OP2 output to a logic 1. (normal default
condition)
Logic 1 = Set -OP2 output to a logic 0.
MCR BIT-4:
Logic 0 = Disable loop-back mode. (normal default
condition)
Logic 1 = Enable local loop-back mode (diagnostics).
MCR BIT 5-7: Not used and set to “0”.
Line Status Register (LSR)
This register provides the status of data transfers
between. the ST16C550 and the CPU.
LSR BIT-0:
Logic 0 = No data in receive holding register or FIFO.
(normal default condition)
Logic 1 = Data has been received and is saved in the
receive holding register or FIFO.
LSR BIT-1:
Logic 0 = No overrun error. (normal default condition)
Logic 1 = Overrun error. A data overrun error occurred
in the receive shift register. This happens when addi-
tional data arrives while the FIFO is full. In this case
the previous data in the shift register is overwritten.
Note that under this condition the data byte in the
receive shift register is not transfer into the FIFO,
therefore the data in the FIFO is not corrupted by the
error.
LSR BIT-2:
Logic 0 = No parity error (normal default condition)
Logic 1 = Parity error. The receive character does not
have correct parity information and is suspect. In the
FIFO mode, this error is associated with the character
at the top of the FIFO.
LSR BIT-3:
Logic 0 = No framing error (normal default condition).
Logic 1 = Framing error. The receive character did not
have a valid stop bit(s). In the FIFO mode this error is
associated with the character at the top of the FIFO.
LSR BIT-4:
Logic 0 = No break condition (normal default condi-
tion)
Logic 1 = The receiver received a break signal (RX
was a logic 0 for one character frame time). In the
FIFO mode, only one break character is loaded into
the FIFO.
LSR BIT-5:
This bit is the Transmit Holding Register Empty indi-
cator. This bit indicates that the UART is ready to
accept a new character for transmission. In addition,
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C1450CJ28TR-F | IC UART FIFO 1B 28PLCC |
| 2-1776266-1 | TERM BLK SIDE ENTRY 21POS 5MM |
| 1-1393117-7 | RELAY GEN PURPOSE DPDT 5A 120V |
| 2-1776266-2 | TERM BLK SIDE ENTRY 22POS 5MM |
| 2-1776266-3 | TERM BLK SIDE ENTRY 23POS 5MM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C552 | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 16-BYTE FIFO AND PARALLEL PRINTER PORT |
| ST16C552ACJ68 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Exar Corporation 功能描述: |
| ST16C552ACJ68-F | 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO&PARALELPRNTPORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C552ACJ68TR-F | 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO&PARALELPRNTPORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C552AIJ68 | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 16-BYTE FIFO AND PARALLEL PRINTER PORT |
發布緊急采購，3分鐘左右您將得到回復。