- 您現在的位置：買賣IC網 > PDF目錄3762 > ST16C552ACJ68TR-F (Exar Corporation)IC UART FIFO 16B DUAL 68PLCC PDF資料下載
參數資料
| 型號： | ST16C552ACJ68TR-F |
| 廠商： | Exar Corporation |
| 文件頁數： | 3/39頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART FIFO 16B DUAL 68PLCC |
| 標準包裝： | 250 |
| 特點： | * |
| 通道數： | 2，DUART |
| FIFO's： | 16 字節 |
| 規程： | 打印機 |
| 電源電壓： | 2.97 V ~ 5.5 V |
| 帶并行端口： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 68-LCC（J 形引線） |
| 供應商設備封裝： | 68-PLCC |
| 包裝： | 帶卷 (TR) |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
11
ST16C552/552A
Rev. 3.40
FIFO Operation
The 16 byte transmit and receive data FIFO’s are
enabled by the FIFO Control Register (FCR) bit-0. The
user can set the receive trigger level via FCR bits 6/
7 but not the transmit trigger level. The transmit
interrupt trigger level is set to 16 following a reset. The
receiver FIFO section includes a time-out function to
ensure data is delivered to the external CPU. An
interrupt is generated whenever the Receive Holding
Register (RHR) has not been read following the load-
ing of a character or the receive trigger level has not
been reached.
Hardware/Software and Time-out Interrupts
The interrupts are enabled by IER bits 0-3. Care must be
taken when handling these interrupts. Following a reset
the transmitter interrupt is enabled, the 552/552A will
issue an interrupt to indicate that transmit holding
register is empty. This interrupt must be serviced prior
to continuing operations. The LSR register provides the
current singular highest priority interrupt only. It could
be noted that CTS and RTS interrupts have lowest
interrupt priority. A condition can exist where a higher
priority interrupt may mask the lower priority CTS/RTS
interrupt(s). Only after servicing the higher pending
interrupt will the lower priority CTS/ RTS interrupt(s) be
reflected in the status register. Servicing the interrupt
without investigating further interrupt conditions can
result in data errors.
When two interrupt conditions have the same priority,
it is important to service these interrupts correctly.
Receive Data Ready and Receive Time Out have the
same interrupt priority (when enabled by IER bit-3).
The receiver issues an interrupt after the number of
characters have reached the programmed trigger
level. In this case the 552/552A FIFO may hold more
characters than the programmed trigger level. Follow-
ing the removal of a data byte, the user should recheck
LSR bit-0 for additional characters. A Receive Time
Out will not occur if the receive FIFO is empty. The time
out counter is reset at the center of each stop bit
received or each time the receive holding register (RHR)
is read (see Figure 4, Receive Time-out Interrupt). The
actual time out value is T (Time out length in bits) = 4 X
P (Programmed word length) + 12. To convert the time
out value to a character value, the user has to consider
the complete word length, including data information
length, start bit, parity bit, and the size of stop bit, i.e.,
1X, 1.5X, or 2X bit times.
Example -A: If the user programs a word length of 7,
with no parity and one stop bit, the time out will be:
T = 4 X 7( programmed word length) +12 = 40 bit times.
The character time will be equal to 40 / 9 = 4.4
characters, or as shown in the fully worked out ex-
ample: T = [(programmed word length = 7) + (stop bit
= 1) + (start bit = 1) = 9]. 40 (bit times divided by 9) =
4.4 characters.
Example -B: If the user programs the word length = 7,
with parity and one stop bit, the time out will be:
T = 4 X 7(programmed word length) + 12 = 40 bit times.
Character time = 40 / 10 [ (programmed word length
= 7) + (parity = 1) + (stop bit = 1) + (start bit = 1) = 4
characters.
Programmable Baud Rate Generator
The 552/552A supports high speed modem technolo-
gies that have increased input data rates by employing
data compression schemes. For example a 33.6Kbps
modem that employs data compression may require a
115.2Kbps input data rate. A 128.0Kbps ISDN modem
that supports data compression may need an input
data rate of 460.8Kbps. The 552/552A can support a
standard data rate of 921.6Kbps.
Single baud rate generator is provided for the trans-
mitter and receiver, allowing independent TX/RX
channel control. The programmable Baud Rate Gen-
erator is capable of accepting an input clock up to 24
MHz, as required for supporting a 1.5Mbps data rate.
The 552/552A requires that an external clock source
be connected to the CLK input pin to clock the internal
baud rate generator for standard or custom rates. (see
Baud Rate Generator Programming below).
The generator divides the input 16X clock by any divisor
from 1 to 216 -1. The 552/552A divides the basic external
clock by 16. The basic 16X clock provides table rates to
support standard and custom applications using the
相關PDF資料 |
PDF描述 |
|---|---|
| ST16C650ACJ44TR-F | IC UART FIFO 32B 44PLCC |
| XR16V2552IL-F | IC UART FIFO 16B DUAL 32QFN |
| XR16L2552IM-F | IC UART FIFO 16B DUAL 48TQFP |
| XR16L2550IL-F | IC UART FIFO 16B DUAL 32QFN |
| ST16C2552CJ44TR-F | IC UART FIFO 16B DUAL 44PLCC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST16C552AIJ68 | 制造商:EXAR 制造商全稱:EXAR 功能描述:DUAL UART WITH 16-BYTE FIFO AND PARALLEL PRINTER PORT |
| ST16C552AIJ68-F | 功能描述:UART 接口集成電路 DUAL UART W/16BYTE FIFO&PARALELPRNTPORT RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| ST16C552CJ | 制造商:STARTECH 功能描述: |
| ST16C552CJ68 | 制造商:Rochester Electronics LLC 功能描述:DUAL PORT 16 BYTE FIFO AND PARALLEL PRINTR - Bulk 制造商:Exar Corporation 功能描述: |
| ST16C552CJ68-F | 功能描述:UART 接口集成電路 2.97V-5.5V 16B FIFO temp 0C to 70C; UART RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。