參數資料
型號： ST52E430B/D
廠商： STMICROELECTRONICS
元件分類： 微控制器/微處理器
英文描述： 8-BIT, UVPROM, 20 MHz, MICROCONTROLLER, CDIP32
封裝： WINDOWED, SHRINK, CERAMIC, DIP-32
文件頁數： 40/120頁
文件大?。?/td> 502K
代理商： ST52E430B/D
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁
26/120
ST52T430/E430
the EPROM operations, changing the Memory
Lock Status from 0 to 1 .
RST_ADD signal resets the memory address
register and the Memory Lock Status. For this
reason, when the RST_ADD becomes high, it is
necessary to unlock the memory to read or write.
INC_ADD signal increments the memory
address.
RST_CONF signal resets the EPROM
Configuration Register. When RST_CONF is
high, the DATA I/O Port A is in output, otherwise
it is always in input.
INC_CONF signal increments the EPROM
Configuration Register value.
PHASE signal validates the operation selected by
means of EPROM Configuration Register value.
3.1.1 EPROM Operation
To execute one EPROM operation (See Table 3.1),
the corresponding identification value must be
loaded in the EPROM Configuration Register. The
signal timing is the following: RST_ADD= high and
PHASE= high, RST_CONF changes from low to
high level, to reset the EPROM Configuration
Register, and INC_CONF signal generates a
number of positive pulses equal to the value to be
loaded. After this sequence, a negative pulse of
the PHASE signal will validate the selected
operation. The minimum PHASE signal pulse
width must be 10 ms for the EPROM Writing
Operation and 100 ns for the others.
When RST_CONF is high, the DATA I/O Port A is
enabled in output and the reading / verify
operation results are available.
After a writing operation, when RST_CONF is high,
the Port A is in output with no valid data.
3.1.2 EPROM Locking
The Memory Lock operation, that is identified with
the number 4 in the EPROM Configuration
Register, writes “0" in the Memory Lock Cell.
At the beginning of an External Operation, when
RST_ADD signal changes from low level to high
level, the Memory Lock Status is “0", therefore it is
necessary to unlock it before to proceed.
To unlock the Memory Lock Status the operation,
that is identified with the number 2 in the EPROM
Configuration Register must be executed (see
Figure 3.2).
The Memory Lock Status can be changed only if
Memory Lock Cell is “1", therefore, for this reason,
after a Memory Lock operation it is not possible to
execute external operations except to read (or
verify) the OTP Code and the Memory Lock Status
3.1.3 EPROM Writing
When the memory is blank, all the bits are at logic
level “1". The data are introduced by programming
only the zeros in the desired memory location;
however all input data must contain both ”1" and
“0".
The only way to change “0" into ”1" is to erase the
whole memory (by exposure to Ultra Violet light)
and reprogram it.
The memory is in Writing mode when the EPROM
Configuration Register value is 3.
The VPP voltage must be 12V±5%, with stable data
on the data bus PA(0:7).
The signals timing is the following (see Figure 3.2):
1) RST_ADD and RST_CONF change from low to
high level,
2) two pulses on INC_CONF signal load the
Memory Unlock operation code,
3) a negative pulse (100 ns) on the PHASE signal
validates the Memory Unlock operation,
4) a negative pulse on RST_CONF signal resets
the EPROM Configuration Register,
5) three positive pulses on INC_CONF load the
Memory Writing operation code,
6) a train of positive pulses on INC_ADD signal
increments the memory location address up to the
requested value (generally this is a sequencial
operation and only one pulse is used),
7) a negative pulse (10 ms) on the PHASE signal
validates the Memory Writing operation,
3.1.4 EPROM Reading / Verify Margin Mode
The reading phase is executed with VPP=5V±5%,
instead of verify phase that needs VPP= 12V±5%.
The Memory Verify operation is available in order
to verify the correctness of the data written. It is
possible to execute a Memory Verify Margin Mode
operation immediately after the writing of each
byte and in this case (see Figure 3.2):
1) a positive pulse on RST_CONF signal resets the
EPROM Configuration Register, if it was not
already reseted
2) one positive pulse on INC_CONF load the
Memory Reading/Verify operation code,
3) a negative pulse (100 ns) on the PHASE signal
validates the Memory Reading / Verify operation,
4) a negative pulse on RST_CONF signal puts in
the PA(0:7) port the value stored in the actual
memory address and resets the EPROM
Configuration Register.
Then, if any error in writing occurred, the user has
to repeat the EPROM writing.
相關PDF資料
PDF描述
ST52F510F1M6 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDSO20
ST52F510G0B6 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDIP28
ST52F513F0M6 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDSO20
ST52F513F1B6 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDIP20
ST52F513G1M6 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDSO28
相關代理商/技術參數
參數描述
ST52E430K1B6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT INTELLIGENT CONTROLLER UNIT ICU Three Timer/PWMs, ADC, SCI
ST52E430K1M6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT INTELLIGENT CONTROLLER UNIT ICU Three Timer/PWMs, ADC, SCI
ST52E430K1T6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT INTELLIGENT CONTROLLER UNIT ICU Three Timer/PWMs, ADC, SCI
ST52E430K2B6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT INTELLIGENT CONTROLLER UNIT ICU Three Timer/PWMs, ADC, SCI
ST52E430K2M6 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT INTELLIGENT CONTROLLER UNIT ICU Three Timer/PWMs, ADC, SCI
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*