- 您現在的位置：買賣IC網 > PDF目錄385870 > ST6228CN6 (意法半導體) ER 5C 5#16S PIN RECP WALL PDF資料下載
參數資料
| 型號： | ST6228CN6 |
| 廠商： | 意法半導體 |
| 英文描述： | ER 5C 5#16S PIN RECP WALL |
| 中文描述： | 8位單片機與微控制器/ D轉換器，自動重加載定時器，UART的秘書長辦公室，安全復位和28引腳封裝 |
| 文件頁數： | 32/84頁 |
| 文件大?。?/td> | 561K |
| 代理商： | ST6228CN6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁
32/84
32
ST62T28C/E28C
3.5 POWER SAVING MODES
The WAIT and STOP modes have been imple-
mented in the ST62xx family of MCUs in order to
reduce theproduct’s electrical consumption during
idle periods. These two power saving modes are
described in the following paragraphs.
3.5.1 WAIT Mode
The MCU goes into WAIT mode as soon as the
WAIT instruction is executed. The microcontroller
can be considered as being in a “software frozen”
state where the core stops processing the pro-
gram instructions, the RAM contents and peripher-
al registers are preserved as long as the power
supply voltage is higher than the RAM retention
voltage. In this mode the peripherals are still ac-
tive.
WAIT mode can be used when the user wants to
reduce the MCU power consumption during idle
periods, while not losing track of time or the capa-
bility of monitoring external events. The active os-
cillator is not stopped in order to provide a clock
signal to the peripherals. Timer counting may be
enabled as well as the Timer interrupt, before en-
tering the WAIT mode: this allows the WAIT mode
to be exited when a Timer interrupt occurs. The
same applies to other peripherals which use the
clock signal.
If the WAIT mode is exited due to a Reset (either
by activating the external pin or generated by the
Watchdog), theMCU enters a normal reset proce-
dure. If an interrupt is generated during WAIT
mode, the MCU’s behaviour depends on the state
of the processor coreprior to the WAIT instruction,
but also on the kind of interrupt request which is
generated. This is described in the following para-
graphs. The processor core does not generate a
delay following the occurrence of the interrupt, be-
cause the oscillator clock is still available and no
stabilisation period is necessary.
3.5.2 STOP Mode
If theWatchdog is disabled, STOP mode is availa-
ble. When in STOP mode, the MCU is placed in
the lowest power consumption mode. In this oper-
ating mode, the microcontrollercan be considered
as being “frozen”, no instruction is executed, the
oscillator is stopped, the RAM contents and pe-
ripheral registers are preserved as long as the
power supply voltage is higher than the RAM re-
tention voltage, and the ST62xx core waits for the
occurrence of an external interrupt request or a
Reset to exit the STOP state.
If the STOP state is exited due to a Reset (byacti-
vating the external pin) the MCU will enter a nor-
mal reset procedure. Behaviour in response to in-
terrupts depends on the state of the processor
core prior to issuing the STOP instruction, and
also on the kind of interrupt request that is gener-
ated.
This case will be described in the following para-
graphs. The processor core generates a delay af-
ter occurrence of the interrupt request, in order to
wait for complete stabilisation of the oscillator, be-
fore executing the first instruction.
相關PDF資料 |
PDF描述 |
|---|---|
| ST6391 | 8-BIT HCMOS MCUs FOR TV FREQUENCY SYNTHESIS WITH OSD |
| ST6392B1 | 8-BIT HCMOS MCUs FOR TV FREQUENCY SYNTHESIS WITH OSD |
| ST6393B1 | 8-BIT HCMOS MCUs FOR TV FREQUENCY SYNTHESIS WITH OSD |
| ST6395B1 | 8-BIT HCMOS MCUs FOR TV FREQUENCY SYNTHESIS WITH OSD |
| ST6391B1 | MOSFET; Transistor Polarity:Dual N Channel; Continuous Drain Current, Id:2.6A; On-Resistance, Rds(on):0.18ohm; Package/Case:8-SOIC; Leaded Process Compatible:No; Mounting Type:surface mount; Peak Reflow Compatible (260 C):No |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST6228CN6/XXX | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| ST622X | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8/16-Bit Micros |
| ST622XC-KIT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:STARTER KIT DATASHEET FOR ST620X. ST621X AND ST622X |
| ST622XC-KIT/110 | 功能描述:開發板和工具包 - 其他處理器 ST622X Starter Kit RoHS:否 制造商:Freescale Semiconductor 產品:Development Systems 工具用于評估:P3041 核心:e500mc 接口類型:I2C, SPI, USB 工作電源電壓: |
| ST622XC-KIT/UK | 制造商:STMicroelectronics 功能描述:ST620 ST621 RS232 STARTER KIT |
發布緊急采購，3分鐘左右您將得到回復。