REV. 5.1.0 ECP/EPP PARALLEL PRINTER PORT WITH 16-BYTE FIFO 4.0 DEVICE OPERATION 4.1 SPP MODE This is ECR mode 000 " />
參數資料
型號： ST78C36ACJ44-F
廠商： Exar Corporation
文件頁數： 3/27頁
文件大小： 0K
描述： IC UART FIFO 16B 44PLCC
標準包裝： 27
特點： *
FIFO's： 16 字節
規程： 打印機
電源電壓： 5V
帶并行端口： 是
安裝類型： 表面貼裝
封裝/外殼： 44-LCC（J 形引線）
供應商設備封裝： 44-PLCC（16.59x16.59）
包裝： 管件
ST78C36/36A
11
REV. 5.1.0
ECP/EPP PARALLEL PRINTER PORT WITH 16-BYTE FIFO
4.0 DEVICE OPERATION
4.1
SPP MODE
This is ECR mode 000 (system RESET mode).
In this output-only mode the host data is registered to PD[7:0] at the trailing edge of -IOW; PDIR is driven low;
-STROBE, -AUTOFD, INIT, and -SLCTIN are open-drain; and all timing is managed by the host through DSR
and DCR registers.
4.2
PS2 MODE
This is ECR mode 001.
In this bi-directional mode the host output data is registered to PD[7:0] at the trailing edge of -IOW, PDIR is
driven by DIR to allow peripheral data input, -AUTOFD, INIT, and -SLCTIN are totem-pole, and all timing is
managed by the host through DSR and DCR registers.
4.3
PPF MODE
This is ECR mode 010.
In this output-only mode the host data is written to the FIFO with I/O writes to address 400 or by DMA writes;
PDIR is driven low; -AUTOFD, INIT, and -SLCTIN are totem-pole.
FIFO data is automatically registered to PD[7:0] whenever the FIFO-E bit is low (data available), and timing is
generated by controller logic that handshakes -STROBE (controller) with BUSY (peripheral).
4.4
ECP MODE
This is ECR mode 011.
In this bi-directional mode the host data is written to the FIFO with I/O writes to address 000, 400 or DMA;
PDIR is driven by DIR (can only be set in ECR mode 001); -AUTOFD, INIT, and -SLCTIN are totem-pole. I/O
writes to address 000 will write a low into the FIFO tag bit, while I/O writes to address 400 or DMA will insert a
high.
4.4.1
ECP FORWARD MODE (PDIR = 0)
FIFO data is automatically registered to PD[7:0] whenever the FIFO-E bit is low (data available), and timing is
generated by controller logic that handshakes -STROBE (controller) with BUSY (peripheral). Data from the
FIFO tag bit is output on -AUTOFD after being registered simultaneous with FIFO data.
相關PDF資料
PDF描述
SW06GSZ-REEL IC SWITCH QUAD SPST 16SOIC
SX1501I087TRT IC GPIO EXPANDER I2C 4CH 20QFN
SX1504I087TRT IC GPIO EXPANDER I2C 4CH 20QFN
SX1509BULTRT IC GPIO EXPANDER I2C 16CH 28QFN
SX8722I070TRLF IC ZOOMING ADC 10BIT 16CH 44MLPQ
相關代理商/技術參數
參數描述
ST78C36ACJ44TR-F 制造商:Exar Corporation 功能描述:UART 1-CH 16Byte FIFO 5V 44-Pin PLCC T/R 制造商:Exar Corporation 功能描述:ST78C36ACJ44TR-F
ST78C36CJ-0A-EVB 功能描述:界面開發工具 Supports 78C36 44 ld PLCC, ISA Interface RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
ST78C36CJ44 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral Interface
ST78C36CJ44F 制造商:N/A 功能描述:NEW
ST78C36CJ44-F 功能描述:接口 - 專用 UART RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*