參數資料
型號： SW90308
英文描述： SW90308 Software Users Manual For MLX90308CCC and MLX90314AB
中文描述： SW90308軟件的用戶MLX90308CCC和MLX90314AB手冊
文件頁數： 21/21頁
文件大?。?/td> 391K
代理商： SW90308
For less than four temperature gaps the last temperature point should be set to 1023. This means
that the last gap extends out to the end of the temperature range.
4.4) Signal linearization
The signal linearization is only available when the device is in digital mode. This means that the
entire calibration procedure should be done in digital mode. A calibration in analog mode may
not yield a valid calibration in digital mode.
It is the best to first do the baseline calibration then linearize the sensor signal and then then
temperature compensation. The baseline offset calibration must be perform in that way that the
digitized signal has the value 0 or 1 LSB ( be careful with clamping at 0 value).
The total number of linearization gaps plus the temperature gaps cannot be more than five. This
is because the temperature coefficients and the linearization coefficients share the same memory
locations.
1) Set all of the PC values to 1024. This corresponds to a real value of +1.000. Also, set P2 thru
P5 to a value of 1023. (P1 = 0)
2) With no signal (zero pressure) find the correct value of P1 to have the correct voltage on the
output.
3) Raise the signal to the signal point (pressure point) P2. This is an arbitrary value (can be
based on where the output varies from the desired output by a set amount). Adjust the output to
the desired level by adjusting PC1.
4) Set P2 by copying the pressure value by copying the digitized pressure value to the P2
location. This must happen after step 3.
5) Repeat steps 3 and 4 for P3, P4, and P5 setting PC2, PC3, and PC4.
6) Raise the pressure to its maximum and set PC5
If fewer than 5 pressure gaps are used the last P value (highest) should be set to 1023.
MLX90308CCC & MLX90314AB Software Users Manual
Rev 2.0
21
11/28/01
相關PDF資料
PDF描述
DK90308 DK90308 Demo Kit for MLX90308
DK90314 DK90314 Demo Kit for MLX90314
SWA010 REINIGUNGSZUBEHOER KUNSTOFFSPACHTEL Inhalt pro Packung: 10 Stk.
SWA400H REINIGER LOESUNGSMITTEL 400ML AEROSOL
SWA12D Analog IC
相關代理商/技術參數
參數描述
SW-90-B 制造商:Sato Parts USA 功能描述:
SW90D/001 制造商:Hart Scientific / Fluke 功能描述:
SW-90-R 制造商:Sato Parts USA 功能描述:
SW90W 功能描述:FLUKEVIEW SCOPEMETER RoHS:是 類別:測試設備 >> 配件 系列:ScopeMeter® 190 標準包裝:1 系列:Anaheim Scientific 類型:專用 附件類型:三腳架 適用于相關產品:儀表 技術規格:- 配用:BK725-ND - DATALOG HUMID/TEMP METER W/DL INBK720-ND - HUMIDITY/TEMP METER W/DUAL INPUT 其它名稱:BKTRISND
SW-90-W 制造商:Sato Parts USA 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*