參數資料
| 型號： | SY87701ALHG TR |
| 廠商： | Micrel Inc |
| 文件頁數： | 15/15頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CLOCK/DATA RECOVERY 32-TQFP |
| 標準包裝： | 1,000 |
| 系列： | AnyRate® |
| 類型： | 時鐘和數據恢復（CDR），多路復用器 |
| PLL： | 是 |
| 主要目的： | 以太網，SONET/SDH，ATM 應用 |
| 輸入： | PECL |
| 輸出： | PECL |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:3 |
| 差分 - 輸入:輸出： | 是/是 |
| 頻率 - 最大： | 1.3Gbps |
| 電源電壓： | 3.15 V ~ 3.45 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-TQFP 裸露焊盤 |
| 供應商設備封裝： | 32-EPAD-TQFP |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | SY87701ALHGTR SY87701ALHGTR-ND |
2011 Microchip Technology Inc.
DS25009C-page 9
MCP7940X
FIGURE 4-2:
ACKNOWLEDGE TIMING
4.1.2
DEVICE ADDRESSING AND OPERATION
A control byte is the first byte received following the
Start condition from the master device (Figure 4-2).
The control byte consists of a control code; for the
MCP7940X this is set as ‘1010111’ for read and write
operations for the Unique ID after the correct unlock
sequence.
The control byte for accessing the SRAM and RTCC
registers are set to ‘1101111’. The RTCC registers and
the SRAM share the same address space.
The last bit of the control byte defines the operation to
be performed. When set to a ‘1’ a read operation is
selected, and when set to a ‘0’ a write operation is
selected. The next byte received defines the address of
the data byte (Figure 4-3). The upper address bits are
transferred first, followed by the Least Significant bits
(LSb).
Following the Start condition, the MCP7940X monitors
the SDA bus, checking the device type identifier being
transmitted.
Upon
receiving
an
‘1010111’ or
‘1101111’ code, the slave device outputs an
Acknowledge signal on the SDA line. Depending on the
state of the R/W bit, the MCP7940X will select a read
or write operation.
FIGURE 4-3:
ADDRESS SEQUENCE BIT ASSIGNMENTS
SCL
9
8
7
6
5
4
3
2
11
2
3
Transmitter must release the SDA line at this point
allowing the Receiver to pull the SDA line low to
acknowledge the previous eight bits of data.
Receiver must release the SDA line at this point
so the Transmitter can continue sending data.
Data from transmitter
SDA
Acknowledge
Bit
1
010
R/W
1
A
0
11
1
0
A
Unique ID CONTROL BYTE
ADDRESS BYTE
CONTROL
CODE
111
X = Don’t Care
1
101
R/W
X
A
0
SRAM RTCC CONTROL BYTE
ADDRESS BYTE
CONTROL
CODE
111
X = Don’t Care
21
相關PDF資料 |
PDF描述 |
|---|---|
| XRT91L34IVTR-F | IC MULTIRATE CDR QUAD 128LQFP |
| VI-210-MX-F3 | CONVERTER MOD DC/DC 5V 75W |
| VI-J4D-MX-F3 | CONVERTER MOD DC/DC 85V 75W |
| VI-J4D-MX-F2 | CONVERTER MOD DC/DC 85V 75W |
| VI-J4D-MX-F1 | CONVERTER MOD DC/DC 85V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SY87701ALHI | 制造商:Synergy 功能描述: 制造商:Micrel Inc 功能描述: |
| SY87701ALZG | 功能描述:計時器和支持產品 3.3V Any-Rate 32-1250 Mbps CDR (I Temp, Green/28 Pin SOIC/Bulk) RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| SY87701ALZG TR | 功能描述:計時器和支持產品 3.3V Any-Rate 32-1250 Mbps CDR (I Temp, Green/28 pin SOIC/T+R) RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| SY87701ALZI | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:3.3V 28Mbps to 1.3Gbps AnyRate Clock and Data Recovery |
| SY87701L | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:3.3V 32-1250Mbps AnyRate CLOCK AND DATA RECOVERY Use lower-power SY87701AL for new designs |
發布緊急采購，3分鐘左右您將得到回復。