- 您現在的位置：買賣IC網 > PDF目錄9660 > SY87701ALZG TR (Micrel Inc)IC CLOCK/DATA RECOVERY 28-SOIC PDF資料下載
參數資料
| 型號： | SY87701ALZG TR |
| 廠商： | Micrel Inc |
| 文件頁數： | 5/15頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CLOCK/DATA RECOVERY 28-SOIC |
| 標準包裝： | 1,000 |
| 系列： | AnyRate® |
| 類型： | 時鐘和數據恢復（CDR），多路復用器 |
| PLL： | 是 |
| 主要目的： | 以太網，SONET/SDH，ATM 應用 |
| 輸入： | PECL |
| 輸出： | PECL |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:3 |
| 差分 - 輸入:輸出： | 是/是 |
| 頻率 - 最大： | 1.3Gbps |
| 電源電壓： | 3.15 V ~ 3.45 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 28-SOIC |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | SY87701ALZGTR SY87701ALZGTR-ND |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
2011 Microchip Technology Inc.
DS25009C-page 13
MCP7940X
5.1.1
RTCC REGISTER ADDRESSES
0x00h – Contains the BCD seconds and 10 seconds.
The range is 00 to 59. Bit 7 in this register is used to
start or stop the on-board crystal oscillator. Setting this
bit to a ‘1’ starts the oscillator and clearing this bit to a
‘0’ stops the on-board oscillator.
0x01h – Contains the BCD minutes and 10 minutes.
The range is 00 to 59.
0x02h – Contains the BCD hour in bits 3:0. Bits 5:4
contain either the 10 hour in BCD for 24-hour format or
the AM/PM indicator and the 10-hour bit for 12-hour
format. Bit 6 determines the hour format. Setting this
bit to ‘0’ enables 24-hour format, setting this bit to ‘1’
enables 12-hour format.
0x03h – Contains the BCD day. The range is 1-7.
Additional bits are also used for configuration and
status.
Bit 3 is the VBATEN bit. If this bit is set, the
internal circuitry is connected to the VBAT pin
when VCC fails. If this bit is ‘0’ then the VBAT pin is
disconnected and the only current drain on the
external battery is the VBAT pin leakage.
Bit 4 is the VBAT bit. This bit is set by hardware
when the VCC fails and the VBAT is used to power
the Oscillator and the RTCC registers. This bit is
cleared by software. Clearing this bit will also
clear all the time-stamp registers.
Bit 5 is the OSCON bit. This is set and cleared by
hardware. If this bit is set, the oscillator is running,
if cleared, the oscillator is not running. This bit
does not indicate that the oscillator is running at
the correct frequency. The RTCC will wait 32
oscillator cycles before the bit is set. The RTCC
will wait roughly 32 clock cycles to clear this bit.
0x04h – Contains the BCD date and 10 date. The
range is 01-31. Bits 5:4 contain 10’s date and bits 4:0
contain the date.
0x05h – Contains the BCD month. Bit 4 contains the
10 month. Bit 5 is the Leap Year bit, which is set during
a leap year and is read-only.
0x06h – Contains the BCD year and 10 year. The
Range is 00-99.
0x07h – Is the Control register.
Bit 7 is the OUT bit. This sets the logic level on the
MFP when not using this as a square wave out-
put.
Bit 6 is the SQWE bit. Setting this bit enables the
divided output from the crystal oscillator.
Bits 5:4 determine which alarms are active.
- 00 – No Alarms are active
- 01 – Alarm 0 is active
- 10 – Alarm 1 is active
- 11 – Both Alarms are active
Bit 3 is the EXTOSC enable bit. Setting this bit will
allow an external 32.768 kHz signal to drive the
RTCC registers, eliminating the need for an
external crystal.
Bit 2:0 sets the internal divider for the 32.768 kHz
oscillator to be driven to the MFP. The duty cycle is
50%. The output is responsive to the Calibration
register. The following frequencies are available:
- 000 – 1 Hz
- 001 – 4.096 kHz
- 010 – 8.192 kHz
- 011 – 32.768 kHz
- 1xx enables the Cal output function. Cal
output appears on MFP if SQWE is set (64
Hz Nominal). See Section 5.2.2 “Calibra-
tion” for more details.
0x08h is the Calibration register. This is an 8-bit
register that is used to add or subtract clocks from the
RTCC counter every minute. The MSB is the sign bit
and indicates if the count should be added or
subtracted. The remaining 7 bits, with each bit adding
or subtracting 2 clocks, give the user the ability to add
or subtract up to 254 clocks per minute.
0x09h is the unlock sequence address. To unlock write
access to the unique ID area in the EEPROM, a
sequence must be written to this address in separate
commands.
The
process
is
fully
detailed
in
0x0Ah-0x0fh and 0x11-0x16h are the Alarm 0 and
Alarm 1 registers. The bits are the same as the RTCC
bits with the following differences:
Locations 0x10h and 0x17h are reserved and should
not be used to allow for future device compatibility.
0x0Dh/0x14h has additional bits for alarm configu-
ration.
ALMxPOL: This bit specifies the level that the
MFP will drive when the alarm is triggered.
ALM2POL is a copy of ALM1POL. The default
state of the MFP when used for alarms is the
inverse of ALM1POL.
ALMxIF: This is the Alarm Interrupt Fag. This bit is
set in hardware if the alarm was triggered. The bit
Note:
The RTCC counters will continue to
increment during the calibration.
相關PDF資料 |
PDF描述 |
|---|---|
| SY87701ALHG TR | IC CLOCK/DATA RECOVERY 32-TQFP |
| XRT91L34IVTR-F | IC MULTIRATE CDR QUAD 128LQFP |
| VI-210-MX-F3 | CONVERTER MOD DC/DC 5V 75W |
| VI-J4D-MX-F3 | CONVERTER MOD DC/DC 85V 75W |
| VI-J4D-MX-F2 | CONVERTER MOD DC/DC 85V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SY87701ALZI | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:3.3V 28Mbps to 1.3Gbps AnyRate Clock and Data Recovery |
| SY87701L | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:3.3V 32-1250Mbps AnyRate CLOCK AND DATA RECOVERY Use lower-power SY87701AL for new designs |
| SY87701L_06 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:3.3V 32-1250Mbps AnyRate CLOCK AND DATA RECOVERY |
| SY87701L_11 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:3.3V 32-1250Mbps AnyRate CLOCK AND DATA RECOVERY Use lower-power SY87701AL for new designs |
| SY87701LGI | 制造商:Micrel Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。