- 您現在的位置：買賣IC網 > PDF目錄373540 > TA1101B (Electronic Theatre Controls, Inc.) Stereo 10W (4з) Class-T⑩ Digital Audio Amplifier using Digital Power Processing⑩ Technology PDF資料下載
參數資料
| 型號： | TA1101B |
| 廠商： | Electronic Theatre Controls, Inc. |
| 元件分類： | 運動控制電子 |
| 英文描述： | Stereo 10W (4з) Class-T⑩ Digital Audio Amplifier using Digital Power Processing⑩ Technology |
| 中文描述： | 10W的立體聲（4з）類- T的數字音頻放大器⑩使用數字電源技術處理⑩ |
| 文件頁數： | 9/13頁 |
| 文件大?。?/td> | 202K |
| 代理商： | TA1101B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁
T E C H N I C A L I N F O R M A T I O N
TA1101B, Rev. 2.2, 08.17.00
9
Amplifier Gain
The gain of the TA1101B is set by the ratio of two external resistors, R
I
and R
F
, and is given by the
following formula:
R
12
V
I
F
I
O
R
V
=
where V
I
is the input signal level and V
O
is the differential output signal level across the speaker.
9 Watts of RMS output power results from an 8.485V RMS signal across an 8
speaker load. If
R
F
= R
I
, then 9 Watts will be achieved with 0.707V RMS of input signal.
)
W
9
8
(
)
P
R
(
V
485
.
O
L
RMS
=
=
Protection Circuits
The TA1101B is guarded against over-temperature and over-current conditions. When the device goes
into an over-temperature or over-current state, the FAULT pin goes to a logic HIGH state indicating a fault
condition. When this occurs, the amplifier is muted, all outputs are TRI-STATED, and will float to 1/2 of
V
DD
.
Over-temperature Protection
An over-temperature fault occurs if the junction temperature of the part exceeds approximately 155
°
C.
The thermal hysteresis of the part is approximately 45
°
C, therefore the fault will automatically clear when
the junction temperature drops below 110
°
C.
Over-current Protection
An over-current fault occurs if more than approximately 7 amps of current flows from any of the amplifier
output pins. This can occur if the speaker wires are shorted together or if one side of the speaker is
shorted to ground. An over-current fault sets an internal latch that can only be cleared if the MUTE pin is
toggled or if the part is powered down. Alternately, if the MUTE pin is connected to the FAULT pin, the
HIGH output of the FAULT pin will toggle the MUTE pin and automatically reset the fault condition.
Overload
The OVERLOADB pin is a 5V logic output. When low, it indicates that the level of the input signal has
overloaded the amplifier resulting in increased distortion at the output. The OVERLOADB signal can be
used to control a distortion indicator light or LED through a simple buffer circuit, as the OVERLOADB
cannot drive an LED directly.
相關PDF資料 |
PDF描述 |
|---|---|
| TA1201CNG | Zener Diode; Application: Low noise; Pd (mW): 250; Vz (V): 4.6 to 5.0; Condition Iz at Vz (mA): 0.5; C (pF) max: -; Condition VR at C (V):   ESD (kV) min: -; Package: DO-35 |
| TA1207F | FOR LCD TVS, PIF AND SIF SYSTEM |
| TA8805F | FOR LCD TVS, PIF AND SIF SYSTEM |
| TA8836F | FOR LCD TVS, PIF AND SIF SYSTEM |
| TA1207 | FOR LCD TVS, PIF AND SIF SYSTEM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TA1104 | 制造商:Tamura Corporation of America 功能描述: |
| TA1105A | 制造商:TAI-SAW 制造商全稱:TAI-SAW 功能描述:SAW Filter 423 MHz |
| TA1108A | 制造商:TAI-SAW 制造商全稱:TAI-SAW 功能描述:SAW Filter 2017.5MHz |
| TA110DU110 | 制造商:ABB Low Voltage Products and Systems 功能描述:O/L RELAY,80-110A |
| TA110DU90 | 制造商:ABB Low Voltage Products and Systems 功能描述:O/L RELAY 65-90A |
發布緊急采購，3分鐘左右您將得到回復。