參數資料
型號: TA8876FA
元件分類: 接收器
英文描述: AUDIO/VIDEO DEMODULATOR, PDSO30
封裝: 0.375 INCH, 1 MM PITCH, PLASTIC, SSOP-30
文件頁數: 13/20頁
文件大?。?/td> 443K
代理商: TA8876FA
TDF8554J
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 1 — 31 August 2011
20 of 56
NXP Semiconductors
TDF8554J
4
45 W power amplifier with multiple voltage regulator
[1]
X = neither mode selected.
7.7 I2C-bus
If pin STB is LOW, the total quiescent current is low, and the I2C-bus lines are not loaded.
When pin STB is switched HIGH, the TDF8554J enters operating mode and performs a
POR which results in pin DIAG going LOW. The TDF8554J starts when IB1[D0] = 1. Bit
D0 also resets the ‘power-on reset occurred’ bit (DB2[D7]) and releases pin DIAG.
Soft mute and hard mute can be activated via the I2C-bus. Soft mute can be activated
independently for the front channels (1 and 3) and rear channels (2 and 4), and mutes the
audio in 15 ms. Hard mute activates the mute for all channels at the same time and mutes
the audio in 400
s. Unmuting after a hard mute will be a soft unmute of approximately
15 ms. When pin STB is switched to standby mode, and the amplifier has started, first the
hard mute is activated and then the amplifier shuts down. It is possible to fully mute the
amplifiers within 400
s by making pin STB LOW, for example during an engine start.
7.8 I2C-bus diagnostic bits read out/cleared after read
The amplifier’s diagnostic information can be read via the I2C-bus. The I2C-bus bits are
set on a failure and will be reset with the I2C-bus read command (clear after read). Even
when the failure is removed the microprocessor will know what was wrong by reading the
I2C-bus. Old information is read during an I2C-bus read. Most up-to-date information is
read after two consecutive read commands.
Cleared after read means that the I2C-bus bits are cleared after a read command. The
Clear command is done only if all four data bytes are read. If only three data bytes are
read, the I2C-bus latches are not cleared and the old value remains in the latches.
When selected, pin DIAG will give up-to-date diagnostic information. When a failure is
removed, pin DIAG will be released instantly, independently of the I2C-bus latches.
8.
Functional description voltage regulator section
The voltage regulator section contains:
Four switchable regulators and one permanent active regulator
Two power switches with loss-of-ground protection
Reset push-pull output
Backup functionality
Table 7.
DC output voltage as a function of different gain settings
Channels 1 and 3
gain setting (dB)
Channels 2 and 4
gain setting (dB)
Line driver/low gain
All channels DC
output voltage (V)
26
X
0.5VP
16
26
X
0.5VP
26
16
X
0.5VP
16
low gain mode
0.5VP
16
line driver mode
0.23VP
相關PDF資料
PDF描述
TA8880AN SPECIALTY CONSUMER CIRCUIT, PDIP64
TA8880CN SPECIALTY CONSUMER CIRCUIT, PDIP64
TA8884AN SPECIALTY CONSUMER CIRCUIT, PDIP54
TA8889AP SPECIALTY CONSUMER CIRCUIT, PDIP16
TA8891N SPECIALTY CONSUMER CIRCUIT, PDIP30
相關代理商/技術參數
參數描述
TA8879 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:1 CHIP NTSC COLOR TV
TA8879N 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:1 CHIP NTSC COLOR TV
TA8880BN 制造商:Panasonic Industrial Company 功能描述:IC
TA8880CN 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:VIDEO, CHROMA, AND SYNC. SIGNAL PROCESSING IC FOR PAL/NTSC/SECAM-SYSTEM COLOR TELEVISIONS
TA8884AN 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:RGB PROCESSOR IC