- 您現(xiàn)在的位置：買賣IC網 > PDF目錄272834 > TC646EUA BRUSHLESS DC MOTOR CONTROLLER, PDSO8 PDF資料下載
參數資料
| 型號： | TC646EUA |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| 封裝： | PLASTIC, MSOP-8 |
| 文件頁數： | 24/28頁 |
| 文件大?。?/td> | 473K |
| 代理商： | TC646EUA |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁
2002 Microchip Technology Inc.
DS21446C-page 5
TC646
2.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 2-1.
TABLE 2-1:
PIN FUNCTION TABLE
2.1
Analog Input (VIN)
The thermistor network (or other temperature sensor)
connects to the VIN input. A voltage range of 1.25V to
2.65V (typical) on this pin drives an active duty cycle of
0% to 100% on the VOUT pin. The TC646 enters shut-
down mode when VIN ≤ VSHDN. During shutdown, the
FAULT output is inactive, and supply current falls to
25 A (typical). The TC646 exits shutdown mode
Applications”, for details).
2.2
Analog Output (CF)
CF is the positive terminal for the PWM ramp generator
timing capacitor. The recommended CF is 1 F for
30 Hz PWM operation.
2.3
Analog Input (VAS)
An external resistor divider connected to the VAS input
sets the auto-shutdown threshold. Auto-shutdown
occurs when VIN ≤ VAS. The fan is automatically
“Typical Applications”, for more details).
2.4
Ground (GND)
GND denotes the ground terminal.
2.5
Analog Input (SENSE)
Pulses are detected at the SENSE pin as fan rotation
chops the current through a sense resistor (RSENSE).
The absence of pulses indicates a fault (see
Section 5.0, “Typical Applications”, for more details).
2.6
Digital Output (FAULT)
The FAULT line goes low to indicate a fault condition.
When FAULT goes low due to a fan fault condition, the
device is latched in shutdown mode until deliberately
cleared or until power is cycled. FAULT will also be
asserted when the PWM reaches 100% duty cycle,
indicating that maximum cooling capability has been
reached and a possible over-temperature condition
may occur. This is a non-latching state and the FAULT
output will go high when the PWM duty cycle goes
below 100%.
2.7
Digital Output (VOUT)
VOUT is an active high complimentary output that drives
the base of an external NPN transistor (via an appropri-
ate base resistor) or the gate of an N-channel MOS-
FET. This output has asymmetrical drive (see
Section 1.0, “Electrical Characteristics”).
2.8
Power Supply Input (VDD)
VDD may be independent of the fan’s power supply
(see Section 1.0, “Electrical Characteristics”).
Pin No.
Symbol
Description
1VIN
Analog Input
2CF
Analog Output
3VAS
Analog Input
4
GND
Ground Terminal
5
SENSE
Analog Input
6FAULT
Digital (Open Collector) Output
7VOUT
Digital Output
8VDD
Power Supply Input
相關PDF資料 |
PDF描述 |
|---|---|
| TLE6210C | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, UUC19 |
| TQD080Z2.0-A83V | 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| TQD080Z2.0-AN93V | 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| TLV431AIDBZR | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 1.24 V, PDSO3 |
| TPS60204DGSG4 | SWITCHED CAPACITOR REGULATOR, 400 kHz SWITCHING FREQ-MAX, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC646EUA713 | 功能描述:馬達/運動/點火控制器和驅動器 Shtdn & Fault Dtct RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TC646VOA | 功能描述:馬達/運動/點火控制器和驅動器 Shtdn & Fault Dtct RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TC646VOA713 | 功能描述:馬達/運動/點火控制器和驅動器 Shtdn & Fault Dtct RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TC646VPA | 功能描述:馬達/運動/點火控制器和驅動器 Shtdn & Fault Dtct RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TC646VUA | 功能描述:馬達/運動/點火控制器和驅動器 Shtdn & Fault Dtct RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發(fā)布緊急采購，3分鐘左右您將得到回復。