- 您現在的位置：買賣IC網 > PDF目錄272834 > TC646EUA BRUSHLESS DC MOTOR CONTROLLER, PDSO8 PDF資料下載
參數資料
| 型號： | TC646EUA |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, PDSO8 |
| 封裝： | PLASTIC, MSOP-8 |
| 文件頁數： | 3/28頁 |
| 文件大?。?/td> | 473K |
| 代理商： | TC646EUA |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
2002 Microchip Technology Inc.
DS21446C-page 11
TC646
5.1
Temperature Sensor Design
The temperature signal connected to VIN must output a
voltage in the range of 1.25V to 2.65V (typical) for 0%
to 100% of the temperature range of interest. The
circuit in Figure 5-2 illustrates a convenient way to
provide this signal.
FIGURE 5-2:
Temperature Sensing
Circuit.
Figure 5-2 shows a simple temperature dependent
voltage divider circuit. RT1 is a conventional NTC ther-
mistor, while R1 and R2 are standard resistors. The
supply voltage, VDD, is divided between R2 and the
parallel combination of RT1 and R1. For convenience,
the parallel combination of RT1 and R1 will be referred
to as RTEMP. The resistance of the thermistor at various
temperatures is obtained from the manufacturer’s
specifications. Thermistors are often referred to in
terms of their resistance at 25°C.
Generally, the thermistor shown in Figure 5-2 is a non-
linear device with a negative temperature coefficient
used to linearize the thermistor temperature response
and R2 is used to produce a positive temperature
coefficient at the VIN node. As an added benefit, this
configuration produces an output voltage delta of 1.4V,
which is well within the range of the VC(SPAN)
specification of the TC646. A 100 k
NTC thermistor is
selected for this application in order to keep IDIV at a
minimum.
For the voltage range at VIN to be equal to 1.25V to
2.65V, the temperature range of this configuration is
0°C to 50°C. If a different temperature range is required
from this circuit, R1 should be chosen to equal the
resistance value of the thermistor at the center of this
new temperature range. It is suggested that a maxi-
mum temperature range of 50°C be used with this cir-
cuit due to thermistor linearity limitations. With this
change, R2 is adjusted according to the following
equations:
EQUATION
These two equations facilitate solving for the two
unknown variables, R1 and R2. More information about
thermistors may be obtained from AN679, “Tempera-
ture Sensing Technologies”, and AN685, “Thermistors
In Single Supply Temperature Sensing Circuits”, which
can be downloaded from Microchip’s web site at
www.microchip.com.
5.2
Auto-Shutdown Temperature
Design
A voltage divider on VAS sets the temperature where
the part is automatically shut down if the sensed
temperature at VIN drops below the set temperature at
VAS (i.e., VIN < VAS). As with the VIN input, 1.25V to
2.65V corresponds to the temperature range of interest
from T1 to T2, respectively. Assuming that the
temperature sensor network designed above is linearly
related to temperature, the shutdown temperature TAS
is related to T2 and T1 by:
EQUATION
For example, if 1.25V and 2.65V at VIN corresponds to
a temperature range of T1 = 0°C to T2 = 125°C, and the
auto-shutdown temperature desired is 25°C, then VAS
voltage is:
EQUATION
The VAS voltage may be set using a simple resistor
divider as shown in Figure 5-3.
R2 = 23.2k
R1 = 100 k
NTC Thermistor
100 k
@25C
IDIV
VIN
VDD
RT1
VDD x R2
RTEMP (T1) + R2
= V(T1)
RTEMP (T2) + R2
= V(T2)
VDD x R2
Where T1 and T2 are the chosen temperatures and
RTEMP is the parallel combination of the thermistor
and R1.
2.65V - 1.25V
T2 - T1
=
VAS - 1.25V
TAS - T1
VAS =
(
( TAS - T1) + 1.25V
1.4V
)
T2 - T1
VAS =
(25 - 0) + 1.25V = 1.53V
1.4V
(125 - 0)
相關PDF資料 |
PDF描述 |
|---|---|
| TLE6210C | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, UUC19 |
| TQD080Z2.0-A83V | 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| TQD080Z2.0-AN93V | 2-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE |
| TLV431AIDBZR | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 1.24 V, PDSO3 |
| TPS60204DGSG4 | SWITCHED CAPACITOR REGULATOR, 400 kHz SWITCHING FREQ-MAX, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC646EUA713 | 功能描述:馬達/運動/點火控制器和驅動器 Shtdn & Fault Dtct RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TC646VOA | 功能描述:馬達/運動/點火控制器和驅動器 Shtdn & Fault Dtct RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TC646VOA713 | 功能描述:馬達/運動/點火控制器和驅動器 Shtdn & Fault Dtct RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TC646VPA | 功能描述:馬達/運動/點火控制器和驅動器 Shtdn & Fault Dtct RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TC646VUA | 功能描述:馬達/運動/點火控制器和驅動器 Shtdn & Fault Dtct RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。