- 您現在的位置：買賣IC網 > PDF目錄385914 > TCM320AC54N (Texas Instruments, Inc.) MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER PDF資料下載
參數資料
| 型號： | TCM320AC54N |
| 廠商： | Texas Instruments, Inc. |
| 元件分類： | Codec |
| 英文描述： | MONOLITHIC SERIAL INTERFACE COMBINED PCM CODEC AND FILTER |
| 中文描述： | 整體式串行接口的PCM編解碼器和過濾器 |
| 文件頁數： | 13/23頁 |
| 文件大?。?/td> | 317K |
| 代理商： | TCM320AC54N |
TCM320AC36, TCM320AC37
VOICE-BAND AUDIO PROCESSORS (VBAP
)
SLWS003C – MAY 1992 – REVISED APRIL – 1998
13
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
general
system reliability features
The device should be powered up and initialized as follows:
1.
2.
3.
4.
5.
Apply GND.
Apply V
CC
.
Connect all clocks.
Apply TTL high to PDN.
Apply synchronizing pulses to FSX and/or FSR.
Even though the VBAP is heavily protected against latch-up, it is still possible to cause it to latch up under certain
improper power conditions. To help ensure that latch-up does not occur, a reverse-biased Schottky diode (with
a forward voltage drop of less than or equal to 0.4 V — 1N5711 or equivalent) should be connected between
V
CC
(power supply) and GND.
On the transmit channel, digital outputs DOUT and TSX are held in the high-impedance state for approximately
four frames (500
μ
s) after power up or application of V
CC
. After this delay, DOUT, TSX, and signaling are
functional and occur in the correct time slot. The analog circuits on the transmit side require approximately
60 ms to reach their equilibrium value due to the autozero circuit settling time. To further enhance system
integrity, DOUT and TSX are placed in the high-impedance state after an interruption of CLK.
power-down and standby operations
To minimize power consumption, a power-down mode and three standby modes are provided.
For power down, an external low signal is applied to PDN. In the absence of a signal, PDN is internally pulled
up to a high logic level and the device remains active. In the power-down mode, the average power consumption
is reduced to 3 mW.
Three standby modes give the user the option of placing the entire device on standby, placing only the transmit
channel on standby, or placing only the receive channel on standby. To place the entire device on standby, both
FSX and FSR are held low. For transmit-only operation (receive channel on standby), FSX is pulsing and FSR
is held low. For receive-only operation (transmit section on standby), FSR is pulsing and FSX is held low. When
the entire device is in standby mode, power consumption is reduced to 5 mW. See Table 1 for power-down and
standby procedures.
相關PDF資料 |
PDF描述 |
|---|---|
| TCM809(中文) | 3-Pin Microcontroller Reset Monitors(3引腳微控制器復位監控器) |
| TCM810(中文) | 3-Pin Microcontroller Reset Monitors(3引腳微控制器復位監控器) |
| TCM809 | 3-Pin Microcontroller Reset Monitors(3引腳微控制器復位監控器) |
| TCM811(中文) | 4-Pin Microcontroller Reset Monitors(4引腳微控制器復位監控器) |
| TCM812(中文) | 4-Pin Microcontroller Reset Monitors(4引腳微控制器復位監控器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TCM320AC56 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:VOICE-BAND AUDIO PROCESSORS (VBAP?￡a) |
| TCM320AC56CDW | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| TCM320C | 功能描述:MODULE SOC RF TXRX W/8051 MCU RoHS:是 類別:RF/IF 和 RFID >> RF 收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:30 系列:- 頻率:4.9GHz ~ 5.9GHz 數據傳輸率 - 最大:54Mbps 調制或協議:* 應用:* 功率 - 輸出:-3dBm 靈敏度:- 電源電壓:2.7 V ~ 3.6 V 電流 - 接收:* 電流 - 傳輸:* 數據接口:PCB，表面貼裝 存儲容量:- 天線連接器:PCB，表面貼裝 工作溫度:-25°C ~ 85°C 封裝/外殼:68-TQFN 裸露焊盤 包裝:管件 |
| TCM320U | 制造商:EnOcean GmbH 功能描述:MODULE TRANSCEIVER 3V W/PIN CONN |
| TCM323AVBB | 制造商:The Cherry Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。