參數資料
型號: TDA3661AT
廠商: NXP SEMICONDUCTORS
元件分類: 基準電壓源/電流源
英文描述: Very low dropout voltage/quiescent current adjustable voltage regulator
中文描述: 1.5 V-45 V ADJUSTABLE POSITIVE LDO REGULATOR, 0.3 V DROPOUT, PDSO8
封裝: 3.90 MM, PLASTIC, SOP-8
文件頁數: 11/16頁
文件大?。?/td> 88K
代理商: TDA3661AT
9397 750 15049
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 05 — 28 June 2005
11 of 16
Philips Semiconductors
TDA3661
Very low dropout voltage/quiescent current voltage regulator
14. Soldering
14.1 Introduction to soldering surface mount packages
This text gives a very brief insight to a complex technology. A more in-depth account of
soldering ICs can be found in our Data Handbook IC26; Integrated Circuit Packages
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering can still be used for certain surface mount ICs, but it is not suitable for fine pitch
SMDs. In these situations reflow soldering is recommended.
14.2 Reflow soldering
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement. Driven by legislation and
environmental forces the worldwide use of lead-free solder pastes is increasing.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and cooling)
vary between 100 seconds and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215
°
C to 270
°
C depending on solder paste
material. The top-surface temperature of the packages should preferably be kept:
below 225
°
C (SnPb process) or below 245
°
C (Pb-free process)
for all BGA, HTSSON..T and SSOP..T packages
for packages with a thickness
2.5 mm
for packages with a thickness < 2.5 mm and a volume
350 mm
3
so called
thick/large packages.
below 240
°
C (SnPb process) or below 260
°
C (Pb-free process) for packages with a
thickness < 2.5 mm and a volume < 350 mm
3
so called small/thin packages.
Moisture sensitivity precautions, as indicated on packing, must be respected at all times.
14.3 Wave soldering
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal results:
Use a double-wave soldering method comprising a turbulent wave with high upward
pressure followed by a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
larger than or equal to 1.27 mm, the footprint longitudinal axis is
preferred
to be
parallel to the transport direction of the printed-circuit board;
相關PDF資料
PDF描述
TDA3661T Very low dropout voltage/quiescent current adjustable voltage regulator
TDA3825 50 AMP LATCHING POWER RELAY
TDA3845 50 AMP LATCHING POWER RELAY
TDA3845T 50 AMP LATCHING POWER RELAY
TDA4470-MFLG3 Multistandard Video-IF and Quasi Parallel Sound Processing
相關代理商/技術參數
參數描述
TDA3661AT/N1,118 功能描述:低壓差穩壓器 - LDO TDA3661AT/SO8/REEL13//N1 RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓(最大值):307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
TDA3661T 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Very low dropout voltage/quiescent current adjustable voltage regulator
TDA3662 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Very low dropout voltage/quiescent current 3.0 V voltage regulator
TDA3662AT 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Very low dropout voltage/quiescent current 3.0 V voltage regulator
TDA3663 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Very low dropout voltage/quiescent current 3.3 V voltage regulator