- 您現在的位置：買賣IC網 > PDF目錄383940 > TDA4691T (NXP SEMICONDUCTORS) Sync Processor with Clock SPC PDF資料下載
參數資料
| 型號： | TDA4691T |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 信號分離 |
| 英文描述： | Sync Processor with Clock SPC |
| 中文描述： | SYNC SEPARATOR IC, PDSO20 |
| 封裝： | PLASTIC, SOT-163-1, SO-20 |
| 文件頁數： | 6/26頁 |
| 文件大?。?/td> | 206K |
| 代理商： | TDA4691T |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
September 1993
6
Philips Semiconductors
Preliminary specification
Sync Processor with Clock (SPC)
TDA4691
50/60 Hz output
This is an open-collector output,
which is LOW if more than 287
lines/field are detected.
SSC generator
The SSC generator generates a 3
stage super-sandcastle pulse on an
open-collector output, which is able to
operate up to 12 volts. The blanking
thresholds 2.5 V and 4.5 V are
derived from the gap reference (point
16).
Signal identification with Digital
PLL (DPLL)
The analog signal identification with
output signal at pin 4 is completed
with a DPLL. This PLL is able to lock
on the separated sync although the
13.5 MHz VCO is not locked on the
input signal. The ratio of the lock
condition to the unlock condition
influences the voltage at pin 5. The
detector circuit of the analog signal
identification block evaluates the
voltages at pins 2 and 5. If the voltage
at pin 5 reaches 4 V (most of the time
the PLL is locked) pin 4 will be HIGH.
The voltages at pins 2 and 5 together
with the state of the V-logic set the
operation state of the TDA4691. The
TDA4691 is able to accommodate to
different input conditions
automatically.
Some operation conditions can be
set externally by influencing the
voltages at pins 2 and 5:
1.
Time constant T
1
(fast) on:
voltage at pin 2 is limited to
5 V (0 to 5 V).
2.
Time constant T
3
(slow) on:
voltage at pin 5 is limited to
6.2 V (0 to 6.2 V).
3.
Time constant T
3
(slow)
inoperative:
voltage at pin 2 is limited
between 4 V and 6.5 V.
4.
Time constant T
3
(slow)
inoperative with input signal:
voltage at pin 2 is limited to
6.5 V (0 to 6.5 V).
5.
VCO frequency fixed to f
0
:
pin 2 is set to ground
(V
2
<
1 V).
Noise detector
This block switches the time
constant to ‘slow’ if on standard
signal a certain noise level is
reached. This noise level is
measured in a small window
inside the sync pulse.
相關PDF資料 |
PDF描述 |
|---|---|
| TDA4860 | Vertical deflection power amplifier for monitors |
| TDA4861 | Vertical deflection power amplifier for monitors |
| TDA5100A | ASK Transmitter 434 MHz |
| TDA5101 | ASK Transmitter 315 MHz |
| TDA5101A | ASK Transmitter 315 MHz |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA4700 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:Control IC for Single-Ended and Push-Pull Switched-Mode Power Supplies SMPS |
| TDA4700A | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:Control IC for Single-Ended and Push-Pull Switched-Mode Power Supplies SMPS |
| TDA4714A | 制造商:Siemens 功能描述: |
| TDA4714C | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:IC for Switched-Mode Power Supplies (SMPS) |
| TDA4716C | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:IC for Switched-Mode Power Supplies (SMPS) |
發布緊急采購，3分鐘左右您將得到回復。